######2020-09-05######
#######0.04.007#######
######FLASH INFO######
BIN file: tasmota-DE.bin
COM port: (COM7) USB-SERIAL CH340 (Port_#0006.Hub_#0001)
Baud rate: 115200
! FORCED DOUT ENABLED !
######POST FLASH######
No post flash information entered...
######FLASH LOG######
[esptool.exe -vv -bm dout -cd nodemcu -cb 115200 -cp COM7 -ca 0x00000 -cf "E:\Downloads von C\ESPEasy_mega-20190630\bin\tasmota-DE.bin"]
[05.09.2020 12:44:11] esptool v0.4.12 - (c) 2014 Ch. Klippel <ck@atelier-klippel.de>
[05.09.2020 12:44:11] setting flash mode from qio to dout
[05.09.2020 12:44:11] 	setting board to nodemcu
[05.09.2020 12:44:11] 	setting baudrate from 115200 to 115200
[05.09.2020 12:44:11] 	setting port from  to COM7
[05.09.2020 12:44:11] 	setting address from 0x00000000 to 0x00000000
[05.09.2020 12:44:11] 	espcomm_upload_file
[05.09.2020 12:44:11] 	espcomm_upload_mem
[05.09.2020 12:44:11] 	setting serial port timeouts to 1000 ms
[05.09.2020 12:44:11] opening bootloader
[05.09.2020 12:44:11] resetting board
[05.09.2020 12:44:11] trying to connect
[05.09.2020 12:44:11] 	flush start
[05.09.2020 12:44:11] 	setting serial port timeouts to 1 ms
[05.09.2020 12:44:11] 	setting serial port timeouts to 1000 ms
[05.09.2020 12:44:11] 	flush complete
[05.09.2020 12:44:11] 	espcomm_send_command: sending command header
[05.09.2020 12:44:11] 	espcomm_send_command: sending command payload
[05.09.2020 12:44:11] 	read 0, requested 1
[05.09.2020 12:44:11] trying to connect
[05.09.2020 12:44:11] 	flush start
[05.09.2020 12:44:11] 	setting serial port timeouts to 1 ms
[05.09.2020 12:44:11] 	setting serial port timeouts to 1000 ms
[05.09.2020 12:44:11] 	flush complete
[05.09.2020 12:44:11] 	espcomm_send_command: sending command header
[05.09.2020 12:44:11] 	espcomm_send_command: sending command payload
[05.09.2020 12:44:11] 	espcomm_send_command: receiving 2 bytes of data
[05.09.2020 12:44:11] 	espcomm_send_command: receiving 2 bytes of data
[05.09.2020 12:44:11] 	espcomm_send_command: receiving 2 bytes of data
[05.09.2020 12:44:11] 	espcomm_send_command: receiving 2 bytes of data
[05.09.2020 12:44:11] 	espcomm_send_command: receiving 2 bytes of data
[05.09.2020 12:44:11] 	espcomm_send_command: receiving 2 bytes of data
[05.09.2020 12:44:11] 	espcomm_send_command: receiving 2 bytes of data
[05.09.2020 12:44:11] 	espcomm_send_command: receiving 2 bytes of data
[05.09.2020 12:44:11] Uploading 607328 bytes from E:\Downloads von C\ESPEasy_mega-20190630\bin\tasmota-DE.bin to flash at 0x00000000
[05.09.2020 12:44:11] 	erasing flash
[05.09.2020 12:44:11] 	size: 094460 address: 000000
[05.09.2020 12:44:11] 	first_sector_index: 0
[05.09.2020 12:44:11] 	total_sector_count: 149
[05.09.2020 12:44:11] 	head_sector_count: 16
[05.09.2020 12:44:11] 	adjusted_sector_count: 133
[05.09.2020 12:44:11] 	erase_size: 085000
[05.09.2020 12:44:11] 	espcomm_send_command: sending command header
[05.09.2020 12:44:11] 	espcomm_send_command: sending command payload
[05.09.2020 12:44:11] 	setting serial port timeouts to 15000 ms
[05.09.2020 12:44:11] 	read 0, requested 1
[05.09.2020 12:44:11] 	setting serial port timeouts to 1000 ms
[05.09.2020 12:44:11] warning: espcomm_send_command: didn't receive command response
[05.09.2020 12:44:11] warning: espcomm_send_command(FLASH_DOWNLOAD_BEGIN) failed
[05.09.2020 12:44:11] closing bootloader
[05.09.2020 12:44:11] 	flush start
[05.09.2020 12:44:11] 	setting serial port timeouts to 1 ms
[05.09.2020 12:44:11] 	setting serial port timeouts to 1000 ms
[05.09.2020 12:44:11] 	flush complete
[05.09.2020 12:44:11] error: espcomm_upload_mem failed
[2020-09-05 12:44:11] DONE! BUT WITH (1) ERRORS!
############################
[2020-09-05 12:44:11] The COM port was already in use... the post-flash did not complete.
[2020-09-05 12:44:11] JOB COMPLETED, over and out!