Once activated, Wall Plug will keep a connected device ...


Define Z-Wave network alarms to which the Wall Plug will respond.


Parameter defines how the Wall Plug will respond to alarms ...


Wall Plug's alarm mode duration. If a device sending an ...


Parameter defines by how much power load must change ...


Parameter defines by how much power load must change ..


This parameter defines how frequently standard power ...


Changes in energy consumed by controlled devices


Time between reports on power/energy consumption


Metering energy consumed by the Wall Plug itself.

This parameter determines whether energy metering ...


Lower power threshold, used in parameter 52.


Upper power threshold, used in parameter 52.


Turn devices ON when power below DOWN and off ...

Turn devices OFF when power below DOWN ...

Action in case defined power values exceeded

Parameter defines the way 2nd association group devices ...


Power load to make red ring flash violet

Function is active only when parameter 61 is set to 0 or 1.


LED will use predefined steps depending on power

LED will use continuous color depending on power


LED ring illuminated with color before turned off


This function allows for turning off the controlled device...


Minimum variation in load current before a message is sent.


Minutes after which the device will flash if controller communicate is lost


Wheel position on the GreenWave device (read-only)


Default state after power loss


If the LED should indicate a network error by flashing or not


If not zero, automatically switch off after a user defined time


Switch on if load is off else switch off


Switch On if load is Off, else switch Off


value should be set to 1 if the module operates in Venetian Blind mode.


depending on mode, turning time or delay time


only in case of the main controller operation

Parameter influences the lamellas positioning in venetian blind mode


either Toggle switches or a single, momentary switch.


delay till auto turned off or auto gate close


Power threshold to be interpreted as reaching a limit switch.


Time period for the motor to continue operation.


set to 1 will enter calibration mode


0 no change, 1 extreme position


change that needs to occur to trigger the power report


Time to the next report. Value of 0 means the reports are turned off.


Energy threshold to trigger report


if power and energy reports are to sent to the main controller


whether scenes or associations are activated by the switch keys


Forced auto off period


Commands sent when device is turned on/off.

Separation of association sending (key 1)

Activate/Deactivate association sending for group 1 - Also see param #16


Commands sent when device is turned on/off

Commands sent when turned off-last state

Commands sent when turned off-full brightness

![CDATA[NOTE: Parameter 15 value must be set to 1 to work properly.


Follow switch contact (closed=ON, open=OFF)

In case of bi-stable switches, define their behaviour (toggle or follow)


Binary inputs type configuration


Enable/Disable operation of devices associated to group 1


DEACTIVATION - no response to alarm frames


Relay 1: Response to Smoke, CO, CO2 Alarm


Amount of time (ms) the device keeps on flashing after receipt of Alarm Frame


Relay 2: Response to Smoke, CO, CO2 Alarm


Power reports – include self-consumption


Delay time after the plug is switched off


Maximum current the plug can provide to load


Change in power consumption that triggers a report


An over-current notification is sent when the current is higher than this value


System hardware failure (with failure code)


The lower the value, the more sensitive the PIR sensor.


Motion Sensor's Blind Time (Insensitive)

Period of time through which the PIR sensor is “blind”.


Sets the number of moves required for the PIR sensor to report motion.


The higher the value, the more sensitive the PIR sensor.


Period of time after wich Motion alarm will be cancelled.


The parameter determines the part of day in which the PIR sensor will be active.


The parameter defines the difference between night and day.


Determines the command frames sent in 1st association group.


The value of 255 allows to turn ON a device.


The value of 0 allows to turn OFF a device.


The parameter determines the changes in forces.


Time period after which a tamper alarm will be cancelled.


Tamper/No cancellation plus Orientation in space

Tamper/Cancellation plus Orientation in space

Max level of vibrations recorded (Earthquake)

The parameter determines the behaviour of tamper and how it reports.


Tamper alarm is not sent in broadcast mode.

Alarm frame will or will not be sent in broadcast mode.


Change in level of light intensity resulting in illumination report.


Time interval between consecutive illumination reports.


Change in level of temperature resulting in temperature report.


The parameter determines how often the temperature will be measured.


How often temperature reports will be sent to the main controller.


The value to be added to the actual measured temperature.


Flashlight mode - LED glows white 10 seconds

Way in which LED diode behaves after motion has been detected.


The parameter determines the brightness of LED when indicating motion.


Below which LED brightness is set to 1%


Above which LED brightness is set to 100%


Min Temperature Resulting in Blue LED Illumination

This parameter is relevant only when parameter 80 has been properly configured.


Max Temperature Resulting in Red LED Illumination


Indicating mode resembles a police car (white, red and blue).


Whether the alarm is active


For how long the alarm should be active


Wake Device for 10 minutes After Power On


Report only when the defined threshold is exceeded


Defines the difference below or above the upper/lower limit after which the limit is reenabled


Reset Parameters 101-103 to Default Values


Reset Parameters 111-113 to Default Values


Resets all configuration parameters to default setting

Reset the product to factory default setting and exclude from Z-Wave network


Forced auto off period


Automatic turning off relay 1 after set time ...


Map OFF status to all devices in group 1 ...

Sending commands to control devices assigned ...


Assigns bistable key status to the device status.


Binary inputs type configuration


Enable/Disable operation of dimmer or roller shutter devices ...


ALARM FLASHING - relay will turn ON and OFF ...


Amount of time (ms) the device keeps on flashing after receipt of Alarm Frame


Delay before the OFF command is transmitted


Basic Set Command sent when door/window is opened or closed


Setting the BASIC command value to turn on the light


Setting the illumination threshold to turn on the light


Setting the BASIC command value to turn on the light.


Illumination threshold for turning on associated lights.


Time period to wait until reporting motion detected again.


Time to wait before sending command to turn off lights


The interval time for auto reporting the battery level.


The interval time for auto reporting the door/window state


The interval time for auto reporting the illumination state


The interval time for auto reporting the temperature state


The interval time for each auto report tick.


Forced auto off period


Automatic turning off relay 1 after set time ...


Sending commands to control devices assigned ...


Assigns bistable key status to the device status.


Binary inputs type configuration


Enable/Disable operation of dimmer or roller shutter devices ...


Amount of time (ms) the device keeps on flashing after receipt of Alarm Frame


Minimum variation in load current before a message is sent.


Minutes after which the device will flash if controller communicate is lost


Wheel position on the GreenWave device (read-only)


Default state after power loss


If the LED should indicate a network error by flashing or not


Activate/Deactivate association sending for group 1 - Also see param #16


![CDATA[NOTE: Parameter 15 value must be set to 1 to work properly.


In case of bi-stable switches, define their behaviour (toggle or follow)


Enable/Disable operation of devices associated to group 1