Инсталляция под Linux

Bluefox

Всем спасибо.

Сегодня таки удалось установить ioBroker на Raspberry Pi2.

Без проблем поставил сверху ioBroker.vis, даже немного в нём поковырялся.

Но опять вынужден обратиться за помощью - не могу установить ZWave драйвер.

При установке через ioBroker получаю такой лог:

! ````
$ ./iobroker add zwave
npm install iobroker.zwave --production --prefix "/opt/iobroker" (System call)
Package libopenzwave was not found in the pkg-config search path.Perhaps you should add the directory containing libopenzwave.pc' to the PKG_CONFIG_PATH environment variable No package 'libopenzwave' found gyp: Call to 'PKG_CONFIG_PATH= pkg-config --variable=libdir libopenzwave' returned exit status 1\. while trying to load binding.gyp ! gyp ERR! configure error gyp ERR! stack Error: gyp` failed with exit code: 1gyp ERR! stack at ChildProcess.onCpExit (/usr/share/node-gyp/lib/configure.js:344:16)
! gyp ERR! stack at ChildProcess.emit (events.js:98:17)gyp ERR! stack at Process.ChildProcess._handle.onexit (child_process.js:809:12)
! gyp ERR! System Linux 4.1.17-v7+gyp ERR! command "nodejs" "/usr/bin/node-gyp" "rebuild"
gyp ERR! cwd /opt/iobroker/node_modules/iobroker.zwave/node_modules/openzwave-shared
gyp ERR! node -v v0.10.29
gyp ERR! node-gyp -v v0.12.2
gyp ERR! not ok
! npm WARN
This failure might be due to the use of legacy binary "node"npm WARN
For further explanations, please read/usr/share/doc/nodejs/README.Debian

! npm
ERR! openzwave-shared@1.1.7 install: node-gyp rebuildnpm
ERR! Exit status 1npm
ERR! npm ERR! Failed at the openzwave-shared@1.1.7 install script.
npm ERR! This is most likely a problem with the openzwave-shared package,
npm ERR! not with npm itself.
npm ERR! Tell the author that this fails on your system:
npm ERR! node-gyp rebuild
npm ERR! You can get their info via:
! npm ERR! npm owner ls openzwave-sharednpm ERR! There is likely additional logging output above.
! npm
ERR! System Linux 4.1.17-v7+npm ERR! command "/usr/bin/nodejs" "/usr/bin/npm" "install" "iobroker.zwave" "--production" "--prefix" "/opt/iobroker"
npm ERR! cwd /
npm ERR! node -v v0.10.29
npm
ERR! npm -v 1.4.21npm ERR! code ELIFECYCLE
! npm
ERR! Error: EACCES, open 'npm-debug.log'npm
ERR! { [Error: EACCES, open 'npm-debug.log'] errno: 3, code: 'EACCES', path: 'npm-debug.log' }npm ERR!
npm ERR! Please try running this command again as root/Administrator.
! npm ERR! System Linux 4.1.17-v7+
npm ERR! command
"/usr/bin/nodejs" "/usr/bin/npm" "install" "iobroker.zwave" "--production" "--prefix" "/opt/iobroker"npm ERR! cwd /
npm ERR! node -v v0.10.29
npm
ERR! npm -v 1.4.21npm ERR! path npm-debug.log
npm ERR! code EACCES
npm ERR! errno 3
npm ERR! stack Error: EACCES, open 'npm-debug.log'
! npm
ERR! npm ERR! Additional logging details can be found in:
npm ERR! /npm-debug.log
npm ERR!
not ok code 0
ERROR: host.raspberrypi Cannot install iobroker.zwave: 1
ERROR: process exited with code 25
Гуглил по ошибке, наткнулся на совет Bluefox в немецкой ветке установить из консоли:
cd /opt/iobroker
sudo npm install iobroker.zwave
Но, к сожалению, это тоже не помогуло, получаю ошибку при установке open-zwave-master/.lib/hid.o' компонента:

>! ````
root@raspberrypi:/opt/iobroker# npm install iobroker.zwave
-
> iobroker.zwave@0.2.5 preinstall /opt/iobroker/node_modules/iobroker.zwave
> node preinstall.js
>! ---> curl -L -O https://github.com/OpenZWave/open-zwave/archive/master.zip
stdout:
stderr:   % Total    % Received % Xferd  Average Speed   Time    Time     Time  Current
                                 Dload  Upload   Total   Spent    Left  Speed
100   125    0   125    0     0     30      0 --:--:--  0:00:04 --:--:--    30
100 1436k  100 1436k    0     0   218k      0  0:00:06  0:00:06 --:--:--  631k
>! ---> unzip master.zip && rm master.zip
stdout: Archive:  master.zip
8c1073f017a6dc82dc6a07f0d46ffb4c597508f5
   creating: open-zwave-master/
  inflating: open-zwave-master/.gitignore  
inflating: open-zwave-master/ChangeLog  
  inflating: open-zwave-master/INSTALL  
  inflating: open-zwave-master/Makefile  
  inflating: open-zwave-master/README.md  
>! ---------bla-bla-bla-------------------
>!   inflating: open-zwave-master/openzwave.spec  
>! stderr:
---> cd open-zwave-master && make
stdout: CPPFLAGS= make -C /opt/iobroker/node_modules/iobroker.zwave/open-zwave-master/cpp/build/ -
make[1]: Entering directory '/opt/iobroker/node_modules/iobroker.zwave/open-zwave-master/cpp/build'
Building OpenZWave Version 1.4.-1
Building tinystr.o
Building tinyxmlerror.o
Building tinyxml.o
Building tinyxmlparser.o
Building hid.o
/opt/iobroker/node_modules/iobroker.zwave/open-zwave-master/cpp/build/support.mk:124: recipe for target '/opt/iobroker/node_modules/iobroker.zwave/open-zwave-master/.lib/hid.o' failed
make[1]: Leaving directory '/opt/iobroker/node_modules/iobroker.zwave/open-zwave-master/cpp/build'
Makefile:20: recipe for target 'all' failed
>! stderr: /opt/iobroker/node_modules/iobroker.zwave/open-zwave-master/cpp/hidapi/linux/hid.c:44:21: fatal error: libudev.h: No such file or directory
 #include <libudev.h>^
compilation terminated.
make[1]: *** [/opt/iobroker/node_modules/iobroker.zwave/open-zwave-master/.lib/hid.o] Error 1
make: *** [all] Error 2
>! exec error: Error: Command failed: /opt/iobroker/node_modules/iobroker.zwave/open-zwave-master/cpp/hidapi/linux/hid.c:44:21: fatal error: libudev.h: No such file or directory
 #include <libudev.h>^
compilation terminated.
make[1]: *** [/opt/iobroker/node_modules/iobroker.zwave/open-zwave-master/.lib/hid.o] Error 1
make: *** [all] Error 2
>! \
> openzwave-shared@1.1.7 preinstall /opt/iobroker/node_modules/iobroker.zwave/node_modules/openzwave-shared
> node lib/install-ozw.js
>! |
> openzwave-shared@1.1.7 install /opt/iobroker/node_modules/iobroker.zwave/node_modules/openzwave-shared
> node-gyp rebuild
>! Package libopenzwave was not found in the pkg-config search path.
Perhaps you should add the directory containing `libopenzwave.pc'
to the PKG_CONFIG_PATH environment variable
No package 'libopenzwave' found
gyp: Call to 'PKG_CONFIG_PATH= pkg-config --variable=libdir libopenzwave' returned exit status 1\. while trying to load binding.gyp
gyp ERR! configure error
gyp ERR! stack Error: `gyp` failed with exit code: 1
gyp ERR! stack     at ChildProcess.onCpExit (/usr/share/node-gyp/lib/configure.js:344:16)
gyp ERR! stack     at ChildProcess.emit (events.js:98:17)
gyp ERR! stack     at Process.ChildProcess._handle.onexit (child_process.js:809:12)
gyp ERR! System Linux 4.1.17-v7+
gyp ERR! command "nodejs" "/usr/bin/node-gyp" "rebuild"
gyp ERR! cwd /opt/iobroker/node_modules/iobroker.zwave/node_modules/openzwave-shared
gyp ERR! node -v v0.10.29
gyp ERR! node-gyp -v v0.12.2
gyp ERR! not ok
npm WARN This failure might be due to the use of legacy binary "node"
npm WARN For further explanations, please read
/usr/share/doc/nodejs/README.Debian
 
npm ERR! openzwave-shared@1.1.7 install: `node-gyp rebuild`
npm ERR! Exit status 1
npm ERR!
npm ERR! Failed at the openzwave-shared@1.1.7 install script.
npm ERR! This is most likely a problem with the openzwave-shared package,
npm ERR! not with npm itself.
npm ERR! Tell the author that this fails on your system:
npm ERR!     node-gyp rebuild
npm ERR! You can get their info via:
npm ERR!     npm owner ls openzwave-shared
npm ERR! There is likely additional logging output above.
>! npm ERR! System Linux 4.1.17-v7+
npm ERR! command "/usr/bin/nodejs" "/usr/bin/npm" "install" "iobroker.zwave"
npm ERR! cwd /opt/iobroker
npm ERR! node -v v0.10.29
npm ERR! npm -v 1.4.21
npm ERR! code ELIFECYCLE
npm ERR!
npm ERR! Additional logging details can be found in:
npm ERR!     /opt/iobroker/npm-debug.log
npm ERR! not ok code 0
root@raspberrypi:/opt/iobroker#</libudev.h></libudev.h> 
Подскажите, что предпринять в данной ситуации? `
http://forum.iobroker.net/viewtopic.php … =20#p10299

apt-get update && apt-get upgrade
apt-get install unzip
apt-get install libudev-dev

kto

~~@Bluefox:~~

http://forum.iobroker.net/viewtopic.php … =20#p10299
apt-get update && apt-get upgrade
apt-get install unzip
apt-get install libudev-dev
```` `  

Так, unzip был установлен, libudev-dev установился.

Это повлияло в лучшую сторону, но полного успеха всё ещё нет.

При попытке установить через ioBroker:

! ````
$ ./iobroker add zwave
npm install iobroker.zwave --production --prefix "/opt/iobroker" (System call)
In file included from ../src/openzwave.hpp:27:0, from ../src/callbacks.cc:18:
/opt/iobroker/node_modules/iobroker.zwave/node_modules/openzwave-shared/node_modules/nan/nan.h:328:47: error: ‘REPLACE_INVALID_UTF8’ is not a member of ‘v8::String’
static const unsigned kReplaceInvalidUtf8 = v8::String::REPLACE_INVALID_UTF8;
^
! make: *** [Release/obj.target/openzwave_shared/src/callbacks.o] Error 1
gyp
ERR! build error
gyp
ERR! stack Error: make failed with exit code: 2gyp ERR!
stack at ChildProcess.onExit (/usr/share/node-gyp/lib/build.js:267:23)
gyp ERR! stack at ChildProcess.emit (events.js:98:17)gyp ERR! stack at Process.ChildProcess._handle.onexit (child_process.js:809:12)
gyp ERR! System Linux 4.1.17-v7+
gyp ERR! command "nodejs" "/usr/bin/node-gyp" "rebuild"
gyp ERR! cwd /opt/iobroker/node_modules/iobroker.zwave/node_modules/openzwave-shared
gyp ERR!
node -v v0.10.29gyp ERR! node-gyp -v v0.12.2
gyp ERR! not ok
! npm
WARN This failure might be due to the use of legacy binary "node"npm WARN For further explanations, please read
/usr/share/doc/nodejs/README.Debian

! npm
ERR! openzwave-shared@1.1.7 install: node-gyp rebuildnpm ERR! Exit status 1
! npm ERR! npm ERR! Failed at the openzwave-shared@1.1.7 install script.
npm ERR! This is most likely a problem with the openzwave-shared package,
npm ERR! not with npm itself.
npm ERR! Tell the author that this fails on your system:
npm ERR! node-gyp rebuild
npm ERR! You can get their info via:
! npm
ERR! npm owner ls openzwave-sharednpm ERR! There is likely additional logging output above.
! npm ERR! System Linux 4.1.17-v7+
npm ERR! command "/usr/bin/nodejs" "/usr/bin/npm" "install" "iobroker.zwave" "--production" "--prefix" "/opt/iobroker"
npm ERR! cwd /
npm ERR! node -v v0.10.29
npm ERR! npm -v 1.4.21
npm ERR! code ELIFECYCLE
! npm
ERR! Error: EACCES, open 'npm-debug.log'npm ERR! { [Error: EACCES, open 'npm-debug.log'] errno: 3, code: 'EACCES', path: 'npm-debug.log' }
npm ERR!
npm ERR! Please try running this command again as root/Administrator.
! npm
ERR! System Linux 4.1.17-v7+
npm ERR! command "/usr/bin/nodejs" "/usr/bin/npm" "install" "iobroker.zwave" "--production" "--prefix" "/opt/iobroker"
npm ERR! cwd /npm ERR! node -v v0.10.29
npm ERR! npm -v 1.4.21
npm ERR! path npm-debug.log
npm ERR! code EACCES
npm ERR! errno 3
npm ERR! stack Error: EACCES, open 'npm-debug.log'
! npm ERR! npm ERR! Additional logging details can be found in:
npm ERR! /npm-debug.log
npm ERR! not ok code 0
! ERROR: host.raspberrypi Cannot install iobroker.zwave: 1
ERROR: process exited with code 25


Та же ошибка и при установке через консоль:

>! ````
-----бла---бла---бла--------
  inflating: open-zwave-master/openzwave.dsc  
  inflating: open-zwave-master/openzwave.spec  
>! stderr: 
---> cd open-zwave-master && make
stdout: CPPFLAGS= make -C /opt/iobroker/node_modules/iobroker.zwave/open-zwave-master/cpp/build/ - 
make[1]: Entering directory '/opt/iobroker/node_modules/iobroker.zwave/open-zwave-master/cpp/build'
Building OpenZWave Version 1.4.-1
Building tinystr.o
Building tinyxmlerror.o
Building tinyxml.o
-----бла---бла---бла--------
Building vers.o
Linking Static Library
Linking Shared Library
Making ozw_config file
make[1]: Leaving directory '/opt/iobroker/node_modules/iobroker.zwave/open-zwave-master/cpp/build'
CPPFLAGS= make -C /opt/iobroker/node_modules/iobroker.zwave/open-zwave-master/cpp/examples/MinOZW/ - 
make[1]: Entering directory '/opt/iobroker/node_modules/iobroker.zwave/open-zwave-master/cpp/examples/MinOZW'
Building Main.o
Linking /opt/iobroker/node_modules/iobroker.zwave/open-zwave-master/.lib/MinOZW
g++   -o /opt/iobroker/node_modules/iobroker.zwave/open-zwave-master/.lib/MinOZW /opt/iobroker/node_modules/iobroker.zwave/open-zwave-master/.lib/Main.o /opt/iobroker/node_modules/iobroker.zwave/open-zwave-master/libopenzwave.so -pthread
Creating Temporary Shell Launch Script
make[1]: Leaving directory '/opt/iobroker/node_modules/iobroker.zwave/open-zwave-master/cpp/examples/MinOZW'
>! stderr: 
---> cd open-zwave-master && sudo make install
stdout: make -C /opt/iobroker/node_modules/iobroker.zwave/open-zwave-master/cpp/build/ - install
make[1]: Entering directory '/opt/iobroker/node_modules/iobroker.zwave/open-zwave-master/cpp/build'
Making libopenzwave pkg-config file
Installing Shared Library
Installing Headers
Installing Config Database
Installing Documentation
Installing Pkg-config Files
make[1]: Leaving directory '/opt/iobroker/node_modules/iobroker.zwave/open-zwave-master/cpp/build'
make -C /opt/iobroker/node_modules/iobroker.zwave/open-zwave-master/cpp/examples/MinOZW/ - install
make[1]: Entering directory '/opt/iobroker/node_modules/iobroker.zwave/open-zwave-master/cpp/examples/MinOZW'
Installing into Prefix: /usr/local
make[1]: Leaving directory '/opt/iobroker/node_modules/iobroker.zwave/open-zwave-master/cpp/examples/MinOZW'
>! stderr: Makefile:193: Documentation not being built
>! |
> openzwave-shared@1.1.7 preinstall /opt/iobroker/node_modules/iobroker.zwave/node_modules/openzwave-shared
> node lib/install-ozw.js
>! /
> openzwave-shared@1.1.7 install /opt/iobroker/node_modules/iobroker.zwave/node_modules/openzwave-shared
> node-gyp rebuild
>! make: Entering directory '/opt/iobroker/node_modules/iobroker.zwave/node_modules/openzwave-shared/build'
  CXX(target) Release/obj.target/openzwave_shared/src/callbacks.o
In file included from ../src/openzwave.hpp:27:0,
                 from ../src/callbacks.cc:18:
/opt/iobroker/node_modules/iobroker.zwave/node_modules/openzwave-shared/node_modules/nan/nan.h:328:47: error: ‘REPLACE_INVALID_UTF8’ is not a member of ‘v8::String’
   static const unsigned kReplaceInvalidUtf8 = v8::String::REPLACE_INVALID_UTF8;
                                               ^
openzwave_shared.target.mk:105: recipe for target 'Release/obj.target/openzwave_shared/src/callbacks.o' failed
make: *** [Release/obj.target/openzwave_shared/src/callbacks.o] Error 1
make: Leaving directory '/opt/iobroker/node_modules/iobroker.zwave/node_modules/openzwave-shared/build'
gyp ERR! build error 
gyp ERR! stack Error: `make` failed with exit code: 2
gyp ERR! stack     at ChildProcess.onExit (/usr/share/node-gyp/lib/build.js:267:23)
gyp ERR! stack     at ChildProcess.emit (events.js:98:17)
gyp ERR! stack     at Process.ChildProcess._handle.onexit (child_process.js:809:12)
gyp ERR! System Linux 4.1.17-v7+
gyp ERR! command "nodejs" "/usr/bin/node-gyp" "rebuild"
gyp ERR! cwd /opt/iobroker/node_modules/iobroker.zwave/node_modules/openzwave-shared
gyp ERR! node -v v0.10.29
gyp ERR! node-gyp -v v0.12.2
gyp ERR! not ok 
npm WARN This failure might be due to the use of legacy binary "node"
npm WARN For further explanations, please read
/usr/share/doc/nodejs/README.Debian

npm ERR! openzwave-shared@1.1.7 install: `node-gyp rebuild`
npm ERR! Exit status 1
npm ERR! 
npm ERR! Failed at the openzwave-shared@1.1.7 install script.
npm ERR! This is most likely a problem with the openzwave-shared package,
npm ERR! not with npm itself.
npm ERR! Tell the author that this fails on your system:
npm ERR!     node-gyp rebuild
npm ERR! You can get their info via:
npm ERR!     npm owner ls openzwave-shared
npm ERR! There is likely additional logging output above.
>! npm ERR! System Linux 4.1.17-v7+
npm ERR! command "/usr/bin/nodejs" "/usr/bin/npm" "install" "iobroker.zwave"
npm ERR! cwd /opt/iobroker
npm ERR! node -v v0.10.29
npm ERR! npm -v 1.4.21
npm ERR! code ELIFECYCLE
npm ERR! 
npm ERR! Additional logging details can be found in:
npm ERR!     /opt/iobroker/npm-debug.log
npm ERR! not ok code 0

   static const unsigned kReplaceInvalidUtf8 = v8::String::REPLACE_INVALID_UTF8;

Насколько я понял - это вызвано проблемами с версией nodejs.

У меня стоит v0.10.29, в google борются с этой ошибкой другой версией nodejs.

В частности https://github.com/nodesource/distributions .

Насколько это правильный подход? Стоит ему последовать или будут другие рекомендации?

На всякий случай напомню, что ставлю это всё на raspbian, который крутиться на raspberry pi 2B.

spectrekr

~~@kto:~~

Насколько я понял - это вызвано проблемами с версией nodejs.

У меня стоит v0.10.29, в google борются с этой ошибкой другой версией nodejs.

В частности https://github.com/nodesource/distributions .

Насколько это правильный подход? Стоит ему последовать или будут другие рекомендации?

На всякий случай напомню, что ставлю это всё на raspbian, который крутиться на raspberry pi 2B. `

Отмучал!

Выполняем все под рутом.

/etc/init.d/iobroker stop
apt-get update && apt-get -y upgrade && apt-get -y remove nodejs npm && apt-get -y autoremove
wget http://node-arm.herokuapp.com/node_latest_armhf.deb && dpkg -i node_latest_armhf.deb
sed -i 's/^NODECMD=\/usr\/bin\/node/NODECMD=\/usr\/local\/bin\/node/g' /etc/init.d/iobroker.sh
init 6

После того как малинка загрузится, можно ставить ZWave драйвер.
3277_bildschirmfoto_2019-01-25_um_16.36.58.png

spectrekr

Вопрос к Bluefox, а iobroker с 4 node заработал? А то раньше и с 0.12 не всегда стабильно работал.

Haus

~~@kto:~~

~~@Bluefox:~~
http://forum.iobroker.net/viewtopic.php … =20#p10299
apt-get update && apt-get upgrade
apt-get install unzip
apt-get install libudev-dev
```` `  
Так, unzip был установлен, libudev-dev установился.

Это повлияло в лучшую сторону, но полного успеха всё ещё нет.

При попытке установить через ioBroker:

! ````
$ ./iobroker add zwave
npm install iobroker.zwave --production --prefix "/opt/iobroker" (System call)
In file included from ../src/openzwave.hpp:27:0, from ../src/callbacks.cc:18:
/opt/iobroker/node_modules/iobroker.zwave/node_modules/openzwave-shared/node_modules/nan/nan.h:328:47: error: ‘REPLACE_INVALID_UTF8’ is not a member of ‘v8::String’
static const unsigned kReplaceInvalidUtf8 = v8::String::REPLACE_INVALID_UTF8;
^
! make: *** [Release/obj.target/openzwave_shared/src/callbacks.o] Error 1
gyp
ERR! build error
gyp
ERR! stack Error: make failed with exit code: 2gyp ERR!
stack at ChildProcess.onExit (/usr/share/node-gyp/lib/build.js:267:23)
gyp ERR! stack at ChildProcess.emit (events.js:98:17)gyp ERR! stack at Process.ChildProcess._handle.onexit (child_process.js:809:12)
gyp ERR! System Linux 4.1.17-v7+
gyp ERR! command "nodejs" "/usr/bin/node-gyp" "rebuild"
gyp ERR! cwd /opt/iobroker/node_modules/iobroker.zwave/node_modules/openzwave-shared
gyp ERR!
node -v v0.10.29gyp ERR! node-gyp -v v0.12.2
gyp ERR! not ok
! npm
WARN This failure might be due to the use of legacy binary "node"npm WARN For further explanations, please read
/usr/share/doc/nodejs/README.Debian

! npm
ERR! openzwave-shared@1.1.7 install: node-gyp rebuildnpm ERR! Exit status 1
! npm ERR! npm ERR! Failed at the openzwave-shared@1.1.7 install script.
npm ERR! This is most likely a problem with the openzwave-shared package,
npm ERR! not with npm itself.
npm ERR! Tell the author that this fails on your system:
npm ERR! node-gyp rebuild
npm ERR! You can get their info via:
! npm
ERR! npm owner ls openzwave-sharednpm ERR! There is likely additional logging output above.
! npm ERR! System Linux 4.1.17-v7+
npm ERR! command "/usr/bin/nodejs" "/usr/bin/npm" "install" "iobroker.zwave" "--production" "--prefix" "/opt/iobroker"
npm ERR! cwd /
npm ERR! node -v v0.10.29
npm ERR! npm -v 1.4.21
npm ERR! code ELIFECYCLE
! npm
ERR! Error: EACCES, open 'npm-debug.log'npm ERR! { [Error: EACCES, open 'npm-debug.log'] errno: 3, code: 'EACCES', path: 'npm-debug.log' }
npm ERR!
npm ERR! Please try running this command again as root/Administrator.
! npm
ERR! System Linux 4.1.17-v7+
npm ERR! command "/usr/bin/nodejs" "/usr/bin/npm" "install" "iobroker.zwave" "--production" "--prefix" "/opt/iobroker"
npm ERR! cwd /npm ERR! node -v v0.10.29
npm ERR! npm -v 1.4.21
npm ERR! path npm-debug.log
npm ERR! code EACCES
npm ERR! errno 3
npm ERR! stack Error: EACCES, open 'npm-debug.log'
! npm ERR! npm ERR! Additional logging details can be found in:
npm ERR! /npm-debug.log
npm ERR! not ok code 0
! ERROR: host.raspberrypi Cannot install iobroker.zwave: 1
ERROR: process exited with code 25
Та же ошибка и при установке через консоль:

>! ````
-----бла---бла---бла--------
  inflating: open-zwave-master/openzwave.dsc  
  inflating: open-zwave-master/openzwave.spec  
>! stderr: 
---> cd open-zwave-master && make
stdout: CPPFLAGS= make -C /opt/iobroker/node_modules/iobroker.zwave/open-zwave-master/cpp/build/ - 
make[1]: Entering directory '/opt/iobroker/node_modules/iobroker.zwave/open-zwave-master/cpp/build'
Building OpenZWave Version 1.4.-1
Building tinystr.o
Building tinyxmlerror.o
Building tinyxml.o
-----бла---бла---бла--------
Building vers.o
Linking Static Library
Linking Shared Library
Making ozw_config file
make[1]: Leaving directory '/opt/iobroker/node_modules/iobroker.zwave/open-zwave-master/cpp/build'
CPPFLAGS= make -C /opt/iobroker/node_modules/iobroker.zwave/open-zwave-master/cpp/examples/MinOZW/ - 
make[1]: Entering directory '/opt/iobroker/node_modules/iobroker.zwave/open-zwave-master/cpp/examples/MinOZW'
Building Main.o
Linking /opt/iobroker/node_modules/iobroker.zwave/open-zwave-master/.lib/MinOZW
g++   -o /opt/iobroker/node_modules/iobroker.zwave/open-zwave-master/.lib/MinOZW /opt/iobroker/node_modules/iobroker.zwave/open-zwave-master/.lib/Main.o /opt/iobroker/node_modules/iobroker.zwave/open-zwave-master/libopenzwave.so -pthread
Creating Temporary Shell Launch Script
make[1]: Leaving directory '/opt/iobroker/node_modules/iobroker.zwave/open-zwave-master/cpp/examples/MinOZW'
>! stderr: 
---> cd open-zwave-master && sudo make install
stdout: make -C /opt/iobroker/node_modules/iobroker.zwave/open-zwave-master/cpp/build/ - install
make[1]: Entering directory '/opt/iobroker/node_modules/iobroker.zwave/open-zwave-master/cpp/build'
Making libopenzwave pkg-config file
Installing Shared Library
Installing Headers
Installing Config Database
Installing Documentation
Installing Pkg-config Files
make[1]: Leaving directory '/opt/iobroker/node_modules/iobroker.zwave/open-zwave-master/cpp/build'
make -C /opt/iobroker/node_modules/iobroker.zwave/open-zwave-master/cpp/examples/MinOZW/ - install
make[1]: Entering directory '/opt/iobroker/node_modules/iobroker.zwave/open-zwave-master/cpp/examples/MinOZW'
Installing into Prefix: /usr/local
make[1]: Leaving directory '/opt/iobroker/node_modules/iobroker.zwave/open-zwave-master/cpp/examples/MinOZW'
>! stderr: Makefile:193: Documentation not being built
>! |
> openzwave-shared@1.1.7 preinstall /opt/iobroker/node_modules/iobroker.zwave/node_modules/openzwave-shared
> node lib/install-ozw.js
>! /
> openzwave-shared@1.1.7 install /opt/iobroker/node_modules/iobroker.zwave/node_modules/openzwave-shared
> node-gyp rebuild
>! make: Entering directory '/opt/iobroker/node_modules/iobroker.zwave/node_modules/openzwave-shared/build'
  CXX(target) Release/obj.target/openzwave_shared/src/callbacks.o
In file included from ../src/openzwave.hpp:27:0,
                 from ../src/callbacks.cc:18:
/opt/iobroker/node_modules/iobroker.zwave/node_modules/openzwave-shared/node_modules/nan/nan.h:328:47: error: ‘REPLACE_INVALID_UTF8’ is not a member of ‘v8::String’
   static const unsigned kReplaceInvalidUtf8 = v8::String::REPLACE_INVALID_UTF8;
                                               ^
openzwave_shared.target.mk:105: recipe for target 'Release/obj.target/openzwave_shared/src/callbacks.o' failed
make: *** [Release/obj.target/openzwave_shared/src/callbacks.o] Error 1
make: Leaving directory '/opt/iobroker/node_modules/iobroker.zwave/node_modules/openzwave-shared/build'
gyp ERR! build error 
gyp ERR! stack Error: `make` failed with exit code: 2
gyp ERR! stack     at ChildProcess.onExit (/usr/share/node-gyp/lib/build.js:267:23)
gyp ERR! stack     at ChildProcess.emit (events.js:98:17)
gyp ERR! stack     at Process.ChildProcess._handle.onexit (child_process.js:809:12)
gyp ERR! System Linux 4.1.17-v7+
gyp ERR! command "nodejs" "/usr/bin/node-gyp" "rebuild"
gyp ERR! cwd /opt/iobroker/node_modules/iobroker.zwave/node_modules/openzwave-shared
gyp ERR! node -v v0.10.29
gyp ERR! node-gyp -v v0.12.2
gyp ERR! not ok 
npm WARN This failure might be due to the use of legacy binary "node"
npm WARN For further explanations, please read
/usr/share/doc/nodejs/README.Debian
 
npm ERR! openzwave-shared@1.1.7 install: `node-gyp rebuild`
npm ERR! Exit status 1
npm ERR! 
npm ERR! Failed at the openzwave-shared@1.1.7 install script.
npm ERR! This is most likely a problem with the openzwave-shared package,
npm ERR! not with npm itself.
npm ERR! Tell the author that this fails on your system:
npm ERR!     node-gyp rebuild
npm ERR! You can get their info via:
npm ERR!     npm owner ls openzwave-shared
npm ERR! There is likely additional logging output above.
>! npm ERR! System Linux 4.1.17-v7+
npm ERR! command "/usr/bin/nodejs" "/usr/bin/npm" "install" "iobroker.zwave"
npm ERR! cwd /opt/iobroker
npm ERR! node -v v0.10.29
npm ERR! npm -v 1.4.21
npm ERR! code ELIFECYCLE
npm ERR! 
npm ERR! Additional logging details can be found in:
npm ERR!     /opt/iobroker/npm-debug.log
npm ERR! not ok code 0
   static const unsigned kReplaceInvalidUtf8 = v8::String::REPLACE_INVALID_UTF8;
Насколько я понял - это вызвано проблемами с версией nodejs.

У меня стоит v0.10.29, в google борются с этой ошибкой другой версией nodejs.

В частности https://github.com/nodesource/distributions .

Насколько это правильный подход? Стоит ему последовать или будут другие рекомендации?

На всякий случай напомню, что ставлю это всё на raspbian, который крутиться на raspberry pi 2B. `

А эта инструкция не ваш случай?

Installation

First of all, Implemenation is tested only on ARM Linux (e.g. Raspberry Pi (2)).
You need a fully Development Environment (gcc, make,...)

npm install iobroker.zwave does following Steps for you:

Download and install latest openzwave from github
# cd /opt
# curl -L -O https://github.com/OpenZWave/open-zwave/archive/master.zip
# unzip master.zip
# cd open-zwave-master
# make
# sudo make install
After that you have to do the following Steps:

Put your USB Stick into your Server
Check whether the system has recognized the USB stick
# lsusb
# ls -al /dev/ttyA*

Go into iobroker Website and add the Zwave Adapter

Configure zwave Adapter as described
Start the new zwave Adapter instance
wait
-- until the Message "zwave.0 Scan completed" is found in iobroker.log
-- the Object zwave.0.completed has State "true"

kto

~~@spectrekr:~~

Отмучал!

Выполняем все под рутом.
/etc/init.d/iobroker stop
apt-get update && apt-get -y upgrade && apt-get -y remove nodejs npm && apt-get -y autoremove
wget http://node-arm.herokuapp.com/node_latest_armhf.deb && dpkg -i node_latest_armhf.deb
sed -i 's/^NODECMD=\/usr\/bin\/node/NODECMD=\/usr\/local\/bin\/node/g' /etc/init.d/iobroker.sh
init 6
После того как малинка загрузится, можно ставить ZWave драйвер. `
Огромное человеческое спасибище)

Прямо сейчас мучаю Малинку)

Установилось!) Спасибо) Завтра буду пробовать подключить адаптер и проверить работу в целом.

Для справки - теперь версия node - 4.2.1, а npm - 2.14.7.

~~@Haus:~~

А эта инструкция не ваш случай?

! ````
Installation
! First of all, Implemenation is tested only on ARM Linux (e.g. Raspberry Pi (2)).
You need a fully Development Environment (gcc, make,...)
! npm install iobroker.zwave does following Steps for you:
! Download and install latest openzwave from github

cd /opt

curl -L -O https://github.com/OpenZWave/open-zwave/archive/master.zip

unzip master.zip

cd open-zwave-master

make

sudo make install

After that you have to do the following Steps:

! Put your USB Stick into your Server
Check whether the system has recognized the USB stick

lsusb

ls -al /dev/ttyA*

! Go into iobroker Website and add the Zwave Adapter
! Configure zwave Adapter as described
Start the new zwave Adapter instance
wait
-- until the Message "zwave.0 Scan completed" is found in iobroker.log
-- the Object zwave.0.completed has State "true"
```` `

Похоже, я перед тем, как ставить по инструкции Haus'a сделал бекап. Нужно будет проверить и этот метод.

Меня единственное что смущает - так это````
make install


Что скажите?

spectrekr

Нормальная и правильная практика, только не надо удалять исходники после установки.

Когда надо обновить пакет или удалить, делаем

make remove

В папке с иходниками и он удалит все поставленные компоненты.

kto

~~@spectrekr:~~

Нормальная и правильная практика, только не надо удалять исходники после установки.

Когда надо обновить пакет или удалить, делаем
make remove
В папке с иходниками и он удалит все поставленные компоненты. `
Понял, спасибо.

Сегодня с работы пытался завести Zwave. Получилось, хоть и не с первого раза.

При запуске драйвера в лог выпадает такое:

! ````
host-raspberrypi 2016-02-18 12:50:33 error instance system.adapter.zwave.0 terminated with code 6 (uncaught exception)
Error: 2016-02-18 12:50:33 error at Module.load (module.js:356:32)
Error: 2016-02-18 12:50:33 error at Object.Module._extensions..js (module.js:442:10)
Error: 2016-02-18 12:50:33 error at Module._compile (module.js:435:26)
Error: 2016-02-18 12:50:33 error at Object. (/opt/iobroker/node_modules/iobroker.zwave/node_modules/openzwave-shared/lib/openzwave-shared.js:26:19)
Error: 2016-02-18 12:50:33 error at require (module.js:385:17)
Error: 2016-02-18 12:50:33 error at Module.require (module.js:366:17)
Error: 2016-02-18 12:50:33 error at Function.Module._load (module.js:311:12)
Error: 2016-02-18 12:50:33 error at Module.load (module.js:356:32)
Error: 2016-02-18 12:50:33 error at Object.Module._extensions..node (module.js:460:18)
Error: 2016-02-18 12:50:33 error at Error (native)
Error: 2016-02-18 12:50:33 error libopenzwave.so.1.4: cannot open shared object file: No such file or directory
uncaught 2016-02-18 12:50:33 error exception: libopenzwave.so.1.4: cannot open shared object file: No such file or directory


Помог совет из гугла.

Выполнить на Raspberry

sudo ldconfig


После этого стартовал нормально.

Разве что ошибка в логе:

zwave-0 2016-02-18 12:50:51 error ##### Value added: zwave.0.NODE1.BASIC.Basic = 0 index = 0 comclass = 32 instance = 1

Пока не знаю, насколько критично, так как судя по логу, USB свисток оно подтянуло.

zwave-0 2016-02-18 12:50:51 info Scan completed
zwave-0 2016-02-18 12:50:51 info node ready nodeid:1 nodeinfo:{"manufacturer":"Aeotec","manufacturerid":"0x0086","product":"Z-Stick Gen5","producttype":"0x0001","productid":"0x005a","type":"Static PC Controller","name":"","loc":""}
zwave-0 2016-02-18 12:50:51 info nodeid 1 is now available, but maybe not ready
zwave-0 2016-02-18 12:50:51 error ##### Value added: zwave.0.NODE1.BASIC.Basic = 0 index = 0 comclass = 32 instance = 1
zwave-0 2016-02-18 12:50:51 info driver ready: homeid = 3607400198
zwave-0 2016-02-18 12:50:51 info scanning homeid=0xd7048f06...
zwave-0 2016-02-18 12:50:51 info connected: homeid = 1.4.0
zwave-0 2016-02-18 12:50:50 info starting. Version 0.2.5 in /opt/iobroker/node_modules/iobroker.zwave
host-raspberrypi 2016-02-18 12:50:48 info instance system.adapter.zwave.0 started with pid 2361
host-raspberrypi 2016-02-18 12:50:47 info object change system.adapter.zwave.0
host-raspberrypi 2016-02-18 12:50:33 info Restart adapter system.adapter.zwave.0 because enabled

kto

К сожалению не получается воспользоваться Zwave адаптером.

При подключении устройства (Fibaro Switch) получаю целую простыню ошибок:

! ` > zwave-0 2016-02-18 22:33:50 info Scan completed

zwave-0 2016-02-18 22:33:50 info node ready nodeid:11 nodeinfo:{"manufacturer":"FIBARO System","manufacturerid":"0x010f","product":"FGS222 Double Relay Switch 2x1.5kW","producttype":"0x0202","productid":"0x1002","type":"Binary Power

zwave-0 2016-02-18 22:33:50 error ##### Value added: zwave.0.NODE11.SWITCH_BINARY.Switch_2 = false index = 0 comclass = 37 instance = 2

zwave-0 2016-02-18 22:33:50 error ##### Value added: zwave.0.NODE11.SWITCH_BINARY.Switch_1 = false index = 0 comclass = 37 instance = 1

zwave-0 2016-02-18 22:33:50 error ##### Value added: zwave.0.NODE11.POWERLEVEL.Timeout = 0 index = 1 comclass = 115 instance = 1

zwave-0 2016-02-18 22:33:50 error ##### Value added: zwave.0.NODE11.POWERLEVEL.Powerlevel = Normal index = 0 comclass = 115 instance = 1

zwave-0 2016-02-18 22:33:50 error ##### Value added: zwave.0.NODE11.SWITCH_ALL.Switch All = On and Off Enabled index = 0 comclass = 39 instance = 1

zwave-0 2016-02-18 22:33:50 info controller command feedback: state:The command has completed successfully #### error:No error #### helpmsg:ControllerCommand - Completed #### currently not implemented

zwave-0 2016-02-18 22:33:50 info controller command feedback: state:The controller is communicating with the other device to carry out the command #### error:No error #### helpmsg:ControllerCommand - InProgress #### currently not im

zwave-0 2016-02-18 22:33:50 info controller command feedback: state:The command is starting #### error:No error #### helpmsg:ControllerComand - Starting #### currently not implemented

zwave-0 2016-02-18 22:33:50 info controller command feedback: state:The command has completed successfully #### error:No error #### helpmsg:ControllerCommand - Completed #### currently not implemented

zwave-0 2016-02-18 22:33:50 info controller command feedback: state:The controller is communicating with the other device to carry out the command #### error:No error #### helpmsg:ControllerCommand - InProgress #### currently not im

zwave-0 2016-02-18 22:33:50 info controller command feedback: state:The command is starting #### error:No error #### helpmsg:ControllerComand - Starting #### currently not implemented

zwave-0 2016-02-18 22:33:50 error ##### Value added: zwave.0.NODE11.VERSION.Application Version = 2.02 index = 2 comclass = 134 instance = 1

zwave-0 2016-02-18 22:33:50 error ##### Value added: zwave.0.NODE11.VERSION.Protocol Version = 3.52 index = 1 comclass = 134 instance = 1

zwave-0 2016-02-18 22:33:50 error ##### Value added: zwave.0.NODE11.VERSION.Library Version = 3 index = 0 comclass = 134 instance = 1

zwave-0 2016-02-18 22:33:50 error ##### Value added: zwave.0.NODE11.SWITCH_BINARY.Switch_2 = false index = 0 comclass = 37 instance = 2

zwave-0 2016-02-18 22:33:49 error ##### Value added: zwave.0.NODE11.CONFIGURATION.Relay 2: Response to Temperature Alarm = ALARM RELAY ON - relay will turn ON upon receipt of alarm frame index = 43 comclass = 112 instance = 1

zwave-0 2016-02-18 22:33:49 error ##### Value added: zwave.0.NODE11.CONFIGURATION.Relay 2: Response to Smoke, CO, CO2 Alarm = ALARM FLASHING - relay will turn ON and OFF periodically (see param.39) index = 42 comclass = 112 instance

zwave-0 2016-02-18 22:33:49 error ##### Value added: zwave.0.NODE11.CONFIGURATION.Relay 2: Response to Water Flood Alarm = ALARM RELAY OFF - relay will turn OFF upon receipt of alarm frame index = 41 comclass = 112 instance = 1

zwave-0 2016-02-18 22:33:49 error ##### Value added: zwave.0.NODE11.CONFIGURATION.Relay 2: Response to General Alarm = ALARM FLASHING - relay will turn ON and OFF periodically (see param.39) index = 40 comclass = 112 instance = 1

zwave-0 2016-02-18 22:33:49 error ##### Value added: zwave.0.NODE11.CONFIGURATION.ALARM FLASHING alarm time = 88 index = 39 comclass = 112 instance = 1

zwave-0 2016-02-18 22:33:49 error ##### Value added: zwave.0.NODE11.CONFIGURATION.Relay 1: Response to Temperature Alarm = ALARM RELAY ON - relay will turn ON upon receipt of alarm frame index = 33 comclass = 112 instance = 1

zwave-0 2016-02-18 22:33:49 error ##### Value added: zwave.0.NODE11.CONFIGURATION.Relay 1: Response to Smoke, CO, CO2 Alarm = ALARM FLASHING - relay will turn ON and OFF periodically (see param.39) index = 32 comclass = 112 instance

zwave-0 2016-02-18 22:33:49 error ##### Value added: zwave.0.NODE11.CONFIGURATION.Relay 1: Response to Water Flood Alarm = ALARM RELAY OFF - relay will turn OFF upon receipt of alarm frame index = 31 comclass = 112 instance = 1

zwave-0 2016-02-18 22:33:49 error ##### Value added: zwave.0.NODE11.CONFIGURATION.Relay 1: Response to General Alarm = ALARM FLASHING - relay will turn ON and OFF periodically (see param.39) index = 30 comclass = 112 instance = 1

zwave-0 2016-02-18 22:33:49 error ##### Value added: zwave.0.NODE11.CONFIGURATION.Saving state before power faillure = State saved at power failure, all outputs are set to previous state upon power restore index = 16 comclass = 112 i

zwave-0 2016-02-18 22:33:49 error ##### Value added: zwave.0.NODE11.CONFIGURATION.Dimmer/Roller shutter control = Disable Dimmer/Roller shutter control index = 15 comclass = 112 instance = 1

zwave-0 2016-02-18 22:33:49 error ##### Value added: zwave.0.NODE11.CONFIGURATION.Inputs Button/Switch configuration = Bi-stable input (switch) index = 14 comclass = 112 instance = 1

zwave-0 2016-02-18 22:33:49 error ##### Value added: zwave.0.NODE11.CONFIGURATION.Inputs behaviour = Toggle index = 13 comclass = 112 instance = 1

zwave-0 2016-02-18 22:33:49 error ##### Value added: zwave.0.NODE11.CONFIGURATION.Control key #2 behaviour = Device status is checked index = 7 comclass = 112 instance = 1

zwave-0 2016-02-18 22:33:49 error ##### Value added: zwave.0.NODE11.CONFIGURATION.Separation of association sending (key 1) = Map status to all devices in group 1 (default) index = 6 comclass = 112 instance = 1

zwave-0 2016-02-18 22:33:49 error ##### Value added: zwave.0.NODE11.CONFIGURATION.Auto off for relay 2 = 0 index = 5 comclass = 112 instance = 1

zwave-0 2016-02-18 22:33:49 error ##### Value added: zwave.0.NODE11.CONFIGURATION.Auto off for relay 1 = 0 index = 4 comclass = 112 instance = 1

zwave-0 2016-02-18 22:33:49 error ##### Value added: zwave.0.NODE11.CONFIGURATION.Auto off relay after specified time = Manual override disabled index = 3 comclass = 112 instance = 1

zwave-0 2016-02-18 22:33:49 error ##### Value added: zwave.0.NODE11.CONFIGURATION.Enable/Disable ALL ON/OFF = ALL ON active / ALL OFF active index = 1 comclass = 112 instance = 1

zwave-0 2016-02-18 22:33:49 error ##### Value added: zwave.0.NODE11.POWERLEVEL.Acked Frames = 0 index = 9 comclass = 115 instance = 1

zwave-0 2016-02-18 22:33:49 error ##### Value added: zwave.0.NODE11.POWERLEVEL.Test Status = Failed index = 8 comclass = 115 instance = 1

zwave-0 2016-02-18 22:33:49 error ##### Value added: zwave.0.NODE11.POWERLEVEL.Report = undefined index = 7 comclass = 115 instance = 1

zwave-0 2016-02-18 22:33:49 error ##### Value added: zwave.0.NODE11.POWERLEVEL.Test = undefined index = 6 comclass = 115 instance = 1

zwave-0 2016-02-18 22:33:49 error ##### Value added: zwave.0.NODE11.POWERLEVEL.Frame Count = 0 index = 5 comclass = 115 instance = 1

zwave-0 2016-02-18 22:33:49 error ##### Value added: zwave.0.NODE11.POWERLEVEL.Test Powerlevel = Normal index = 4 comclass = 115 instance = 1

zwave-0 2016-02-18 22:33:49 error ##### Value added: zwave.0.NODE11.POWERLEVEL.Test Node = 0 index = 3 comclass = 115 instance = 1

zwave-0 2016-02-18 22:33:49 error ##### Value added: zwave.0.NODE11.POWERLEVEL.Set Powerlevel = undefined index = 2 comclass = 115 instance = 1

zwave-0 2016-02-18 22:33:49 error ##### Value added: zwave.0.NODE11.POWERLEVEL.Timeout = 0 index = 1 comclass = 115 instance = 1

zwave-0 2016-02-18 22:33:49 error ##### Value added: zwave.0.NODE11.POWERLEVEL.Powerlevel = Normal index = 0 comclass = 115 instance = 1

zwave-0 2016-02-18 22:33:49 error ##### Value added: zwave.0.NODE11.VERSION.Application Version = Unknown index = 2 comclass = 134 instance = 1

zwave-0 2016-02-18 22:33:49 error ##### Value added: zwave.0.NODE11.VERSION.Protocol Version = Unknown index = 1 comclass = 134 instance = 1

zwave-0 2016-02-18 22:33:49 error ##### Value added: zwave.0.NODE11.VERSION.Library Version = Unknown index = 0 comclass = 134 instance = 1

zwave-0 2016-02-18 22:33:49 info node ready nodeid:1 nodeinfo:{"manufacturer":"Aeotec","manufacturerid":"0x0086","product":"Z-Stick Gen5","producttype":"0x0001","productid":"0x005a","type":"Static PC Controller","name":"","loc":""}

zwave-0 2016-02-18 22:33:49 info node11: nop, currently not implemented

zwave-0 2016-02-18 22:33:49 error ##### Value added: zwave.0.NODE11.SWITCH_ALL.Switch All = Disabled index = 0 comclass = 39 instance = 1

zwave-0 2016-02-18 22:33:49 error ##### Value added: zwave.0.NODE11.SWITCH_BINARY.Switch_1 = false index = 0 comclass = 37 instance = 1

zwave-0 2016-02-18 22:33:49 info nodeid 1 is now available, but maybe not ready

zwave-0 2016-02-18 22:33:49 error ##### Value added: zwave.0.NODE1.BASIC.Basic = 0 index = 0 comclass = 32 instance = 1

zwave-0 2016-02-18 22:33:49 info driver ready: homeid = 3607400198 `

К величайшему моему сожалению, пока не нахожу, как с этим справиться.

Метод установки от Haus'а так же не помог - не работает без смены версии nodejs.

А даже сменив - получаем всё те-же ошибки.

fotya

Привет.

Не могу установить iobroker на bananapi BPI-M1+.

Перепробовал все или почти все, ну просто не хочет работать . На Raspberry установилась с первого раза.

Может кто подскажет как на это китайское чудо установить? А то уже появилось желание ,упаковать аккуратно в коробочку и выкинуть.

Bluefox

~~@fotya:~~

Привет.

Не могу установить iobroker на bananapi BPI-M1+.

Перепробовал все или почти все, ну просто не хочет работать . На Raspberry установилась с первого раза.

Может кто подскажет как на это китайское чудо установить? А то уже появилось желание ,упаковать аккуратно в коробочку и выкинуть. `
Что пишет то?

пробовал мануально установить (по пакетам)?

fotya

Пробовал, не хочет.

В линуксе я слабоват и может что-то не понимаю.

Делал так -

Смонтировал образ Bananian Linux ,сделал настройки ,а дальше все мои манипуляции ни к чему не привели.

Как это по шагам сделать?

kontakter

Подскажите пароль для root. Образ для bananapi http://www.iobroker.net/?download=2895 .Armbian для BananaPi на сайте своем пишет 1234. Доступа нет.

Bluefox

~~@kontakter:~~

Подскажите пароль для root. Образ для bananapi http://www.iobroker.net/?download=2895 .Armbian для BananaPi на сайте своем пишет 1234. Доступа нет. `
Name: bananapi Passwort: bananapi

if Bananian OS

Name: root Passwort: pi

Bluefox

~~@fotya:~~

Пробовал, не хочет.

В линуксе я слабоват и может что-то не понимаю.

Делал так -

Смонтировал образ Bananian Linux ,сделал настройки ,а дальше все мои манипуляции ни к чему не привели.

Как это по шагам сделать? `
К чему они то привели? Где застрял то? Залогиниться смог? Итд?

fotya

Захожу под "root"

root@bananapi ~ # apt-get update
root@bananapi ~ # apt-get upgrade

устанавливаю "npm" и "nodejs"

root@bananapi ~ # apt-get install curl
root@bananapi ~ # curl -sL https://deb.nodesource.com/setup_5.x | bash -
root@bananapi ~ # apt-get install  nodejs

получается так -````
root@pi ~ # nodejs -v
v5.7.1
root@pi ~ # npm -v
3.6.0

дальше -````
$ cd /opt
$ mkdir iobroker
$ cd iobroker
$ npm install iobroker

получается вот-так -

! npm WARN lifecycle iobroker@0.6.0~install: cannot run in wd %s %s (wd=%s) iobrok er@0.6.0 node lib/setup.js /opt/iobroker/node_modules/iobroker
! /opt/iobroker
! └─┬ iobroker@0.6.0
! └─┬ yargs@4.2.0
! ├── camelcase@2.1.0
! ├─┬ cliui@3.1.0
! │ ├─┬ strip-ansi@3.0.1
! │ │ └── ansi-regex@2.0.0
! │ └── wrap-ansi@1.0.0
! ├── decamelize@1.2.0
! ├─┬ lodash.assign@4.0.6
! │ ├── lodash.keys@4.0.5
! │ └── lodash.rest@4.0.1
! ├─┬ os-locale@1.4.0
! │ └─┬ lcid@1.0.0
! │ └── invert-kv@1.0.0
! ├─┬ pkg-conf@1.1.1
! │ ├─┬ find-up@1.1.2
! │ │ ├── path-exists@2.1.0
! │ │ └─┬ pinkie-promise@2.0.0
! │ │ └── pinkie@2.0.4
! │ ├── object-assign@4.0.1
! │ ├─┬ read-pkg@1.1.0
! │ │ ├─┬ load-json-file@1.1.0
! │ │ │ ├── graceful-fs@4.1.3
! │ │ │ ├─┬ parse-json@2.2.0
! │ │ │ │ └─┬ error-ex@1.3.0
! │ │ │ │ └── is-arrayish@0.2.1
! │ │ │ ├── pify@2.3.0
! │ │ │ └─┬ strip-bom@2.0.0
! │ │ │ └── is-utf8@0.2.1
! │ │ ├─┬ normalize-package-data@2.3.5
! │ │ │ ├── hosted-git-info@2.1.4
! │ │ │ ├─┬ is-builtin-module@1.0.0
! │ │ │ │ └── builtin-modules@1.1.1
! │ │ │ ├── semver@5.1.0
! │ │ │ └─┬ validate-npm-package-license@3.0.1
! │ │ │ ├─┬ spdx-correct@1.0.2
! │ │ │ │ └── spdx-license-ids@1.2.0
! │ │ │ └─┬ spdx-expression-parse@1.0.2
! │ │ │ └── spdx-exceptions@1.0.4
! │ │ └── path-type@1.1.0
! │ └── symbol@0.2.1
! ├── read-pkg-up@1.0.1
! ├── require-main-filename@1.0.1
! ├─┬ string-width@1.0.1
! │ ├─┬ code-point-at@1.0.0
! │ │ └── number-is-nan@1.0.0
! │ └── is-fullwidth-code-point@1.0.0
! ├── window-size@0.2.0
! ├── y18n@3.2.0
! └── yargs-parser@2.1.1
! npm WARN enoent ENOENT: no such file or directory, open '/opt/iobroker/package.j son'
! npm WARN iobroker No description
! npm WARN iobroker No repository field.
! npm WARN iobroker No README data
! npm WARN iobroker No license field.
! npm install iobroker 30.53s user 2.83s system 82% cpu 40.216 total
И не работает.

kontakter

Методом перебора, за час выяснил : пользователь pi, пароль raspberry. Это для образа http://www.iobroker.net/?download=2895 . Для других не знаю.

Bluefox

~~@fotya:~~

Захожу под "root"
root@bananapi ~ # apt-get update
root@bananapi ~ # apt-get upgrade
устанавливаю "npm" и "nodejs"
root@bananapi ~ # apt-get install curl
root@bananapi ~ # curl -sL https://deb.nodesource.com/setup_5.x | bash -
root@bananapi ~ # apt-get install  nodejs
получается так -````
root@pi ~ # nodejs -v
v5.7.1
root@pi ~ # npm -v
3.6.0
дальше -````
$ cd /opt
$ mkdir iobroker
$ cd iobroker
$ npm install iobroker
получается вот-так -

! npm WARN lifecycle iobroker@0.6.0~install: cannot run in wd %s %s (wd=%s) iobrok er@0.6.0 node lib/setup.js /opt/iobroker/node_modules/iobroker
! /opt/iobroker
! └─┬ iobroker@0.6.0
! └─┬ yargs@4.2.0
! ├── camelcase@2.1.0
! ├─┬ cliui@3.1.0
! │ ├─┬ strip-ansi@3.0.1
! │ │ └── ansi-regex@2.0.0
! │ └── wrap-ansi@1.0.0
! ├── decamelize@1.2.0
! ├─┬ lodash.assign@4.0.6
! │ ├── lodash.keys@4.0.5
! │ └── lodash.rest@4.0.1
! ├─┬ os-locale@1.4.0
! │ └─┬ lcid@1.0.0
! │ └── invert-kv@1.0.0
! ├─┬ pkg-conf@1.1.1
! │ ├─┬ find-up@1.1.2
! │ │ ├── path-exists@2.1.0
! │ │ └─┬ pinkie-promise@2.0.0
! │ │ └── pinkie@2.0.4
! │ ├── object-assign@4.0.1
! │ ├─┬ read-pkg@1.1.0
! │ │ ├─┬ load-json-file@1.1.0
! │ │ │ ├── graceful-fs@4.1.3
! │ │ │ ├─┬ parse-json@2.2.0
! │ │ │ │ └─┬ error-ex@1.3.0
! │ │ │ │ └── is-arrayish@0.2.1
! │ │ │ ├── pify@2.3.0
! │ │ │ └─┬ strip-bom@2.0.0
! │ │ │ └── is-utf8@0.2.1
! │ │ ├─┬ normalize-package-data@2.3.5
! │ │ │ ├── hosted-git-info@2.1.4
! │ │ │ ├─┬ is-builtin-module@1.0.0
! │ │ │ │ └── builtin-modules@1.1.1
! │ │ │ ├── semver@5.1.0
! │ │ │ └─┬ validate-npm-package-license@3.0.1
! │ │ │ ├─┬ spdx-correct@1.0.2
! │ │ │ │ └── spdx-license-ids@1.2.0
! │ │ │ └─┬ spdx-expression-parse@1.0.2
! │ │ │ └── spdx-exceptions@1.0.4
! │ │ └── path-type@1.1.0
! │ └── symbol@0.2.1
! ├── read-pkg-up@1.0.1
! ├── require-main-filename@1.0.1
! ├─┬ string-width@1.0.1
! │ ├─┬ code-point-at@1.0.0
! │ │ └── number-is-nan@1.0.0
! │ └── is-fullwidth-code-point@1.0.0
! ├── window-size@0.2.0
! ├── y18n@3.2.0
! └── yargs-parser@2.1.1
! npm WARN enoent ENOENT: no such file or directory, open '/opt/iobroker/package.j son'
! npm WARN iobroker No description
! npm WARN iobroker No repository field.
! npm WARN iobroker No README data
! npm WARN iobroker No license field.
! npm install iobroker 30.53s user 2.83s system 82% cpu 40.216 total
И не работает. `
node 5 не работает. Надо 4 ставить

Bluefox

~~@fotya:~~

Захожу под "root"
root@bananapi ~ # apt-get update
root@bananapi ~ # apt-get upgrade
устанавливаю "npm" и "nodejs"
root@bananapi ~ # apt-get install curl
root@bananapi ~ # curl -sL https://deb.nodesource.com/setup_5.x | bash -
root@bananapi ~ # apt-get install  nodejs
получается так -````
root@pi ~ # nodejs -v
v5.7.1
root@pi ~ # npm -v
3.6.0
дальше -````
$ cd /opt
$ mkdir iobroker
$ cd iobroker
$ npm install iobroker
получается вот-так -

! npm WARN lifecycle iobroker@0.6.0~install: cannot run in wd %s %s (wd=%s) iobrok er@0.6.0 node lib/setup.js /opt/iobroker/node_modules/iobroker
! /opt/iobroker
! └─┬ iobroker@0.6.0
! └─┬ yargs@4.2.0
! ├── camelcase@2.1.0
! ├─┬ cliui@3.1.0
! │ ├─┬ strip-ansi@3.0.1
! │ │ └── ansi-regex@2.0.0
! │ └── wrap-ansi@1.0.0
! ├── decamelize@1.2.0
! ├─┬ lodash.assign@4.0.6
! │ ├── lodash.keys@4.0.5
! │ └── lodash.rest@4.0.1
! ├─┬ os-locale@1.4.0
! │ └─┬ lcid@1.0.0
! │ └── invert-kv@1.0.0
! ├─┬ pkg-conf@1.1.1
! │ ├─┬ find-up@1.1.2
! │ │ ├── path-exists@2.1.0
! │ │ └─┬ pinkie-promise@2.0.0
! │ │ └── pinkie@2.0.4
! │ ├── object-assign@4.0.1
! │ ├─┬ read-pkg@1.1.0
! │ │ ├─┬ load-json-file@1.1.0
! │ │ │ ├── graceful-fs@4.1.3
! │ │ │ ├─┬ parse-json@2.2.0
! │ │ │ │ └─┬ error-ex@1.3.0
! │ │ │ │ └── is-arrayish@0.2.1
! │ │ │ ├── pify@2.3.0
! │ │ │ └─┬ strip-bom@2.0.0
! │ │ │ └── is-utf8@0.2.1
! │ │ ├─┬ normalize-package-data@2.3.5
! │ │ │ ├── hosted-git-info@2.1.4
! │ │ │ ├─┬ is-builtin-module@1.0.0
! │ │ │ │ └── builtin-modules@1.1.1
! │ │ │ ├── semver@5.1.0
! │ │ │ └─┬ validate-npm-package-license@3.0.1
! │ │ │ ├─┬ spdx-correct@1.0.2
! │ │ │ │ └── spdx-license-ids@1.2.0
! │ │ │ └─┬ spdx-expression-parse@1.0.2
! │ │ │ └── spdx-exceptions@1.0.4
! │ │ └── path-type@1.1.0
! │ └── symbol@0.2.1
! ├── read-pkg-up@1.0.1
! ├── require-main-filename@1.0.1
! ├─┬ string-width@1.0.1
! │ ├─┬ code-point-at@1.0.0
! │ │ └── number-is-nan@1.0.0
! │ └── is-fullwidth-code-point@1.0.0
! ├── window-size@0.2.0
! ├── y18n@3.2.0
! └── yargs-parser@2.1.1
! npm WARN enoent ENOENT: no such file or directory, open '/opt/iobroker/package.j son'
! npm WARN iobroker No description
! npm WARN iobroker No repository field.
! npm WARN iobroker No README data
! npm WARN iobroker No license field.
! npm install iobroker 30.53s user 2.83s system 82% cpu 40.216 total
И не работает. `
http://stackoverflow.com/questions/1813 … -run-in-wd

If npm was invoked with root privileges, then it will change the uid to the user account or uid specified by the user config, which defaults to nobody. Set the unsafe-perm flag to run scripts with root privileges.

[sudo] npm install --unsafe-perm

fotya

Ура заработало!

Изменил строку:

curl -sL https://deb.nodesource.com/setup_5.x | sudo -E bash -
````на

curl -sL https://deb.nodesource.com/setup_4.x | sudo -E bash -

и установка так :

npm install iobroker --unsafe-perm

и заработало ,но нет автозапуска. Только через - iobroker start

NEWS

Инсталляция под Linux

cd /opt

curl -L -O https://github.com/OpenZWave/open-zwave/archive/master.zip

unzip master.zip

cd open-zwave-master

make

sudo make install

lsusb

ls -al /dev/ttyA*

Support us

765
Online

31.9k
Users

80.1k
Topics

1.3m
Posts

NEWS

Инсталляция под Linux

cd /opt

curl -L -O https://github.com/OpenZWave/open-zwave/archive/master.zip

unzip master.zip

cd open-zwave-master

make

sudo make install

lsusb

ls -al /dev/ttyA*

Support us

765Online

31.9kUsers

80.1kTopics

1.3mPosts

765
Online

31.9k
Users

80.1k
Topics

1.3m
Posts