Zwave 0.4

Bluefox

Sollte mit

npm install https://github.com/ioBroker/ioBroker.zwave/tarball/master --production

Laufen. Openzwave wird tatsächlich jedes mal neu übersetzt.

Dutchman

~~@Bluefox:~~

Sollte mit
npm install https://github.com/ioBroker/ioBroker.zwave/tarball/master --production
Laufen. Openzwave wird tatsächlich jedes mal neu übersetzt. `

Und das ist auch OK, die librarys werden auch regelmäßig geupdatet und so bekommt man immer die neuste git Source von openzwave (wichtig für neue Controller & Hardware !)

Sent from my iPhone using Tapatalk

AlCalzone

Endlich wieder Internet zuhause, d.h. ich konnte meinen Pi auf die neusten Adapter updaten. zWave tut bisher was es soll, bin aber noch nicht dazu gekommen, meine Greenwave-Dose zu testen. Hier erwarte ich nochmal Schwierigkeiten.

Lenny.CB

@Bluefox: konntest du dir schon mal die OZW-Logs zum Rollo-Problem anschauen?

http://forum.iobroker.net/viewtopic.php … =40#p39974

Bluefox

~~@Lenny.CB:~~

~~@Bluefox:~~

Hast du log dafür? ` ich versuche es mal…

> ****1:) Rollo oben (99) –> setze Wert 50 in Objekte --> Relais "klickt", Rollo fährt nicht, Wert geht wieder auf 99 zurück****

! ````
2016-11-12 20:22:20.887 Info, Node002, SwitchMultilevel::Set - Setting to level 50
2016-11-12 20:22:20.888 Info, Node002, Duration: Default
2016-11-12 20:22:20.888 Detail, Node002, Queuing (Send) SwitchMultilevelCmd_Set (Node=2): 0x01, 0x0b, 0x00, 0x13, 0x02, 0x04, 0x26, 0x01, 0x32, 0xff, 0x25, 0x46, 0x68
2016-11-12 20:22:20.888 Detail, Node002, Queuing (Send) SwitchMultilevelCmd_Get (Node=2): 0x01, 0x09, 0x00, 0x13, 0x02, 0x02, 0x26, 0x02, 0x25, 0x47, 0xa3
2016-11-12 20:22:20.888 Detail,
2016-11-12 20:22:20.889 Info, Node002, Sending (Send) message (Callback ID=0x46, Expected Reply=0x13) - SwitchMultilevelCmd_Set (Node=2): 0x01, 0x0b, 0x00, 0x13, 0x02, 0x04, 0x26, 0x01, 0x32, 0xff, 0x25, 0x46, 0x68
2016-11-12 20:22:20.897 Detail, Node002, Received: 0x01, 0x04, 0x01, 0x13, 0x01, 0xe8
2016-11-12 20:22:20.898 Detail, Node002, ZW_SEND_DATA delivered to Z-Wave stack
2016-11-12 20:22:20.915 Detail, Node002, Received: 0x01, 0x07, 0x00, 0x13, 0x46, 0x00, 0x00, 0x02, 0xaf
2016-11-12 20:22:20.915 Detail, Node002, ZW_SEND_DATA Request with callback ID 0x46 received (expected 0x46)
2016-11-12 20:22:20.915 Info, Node002, Request RTT 26 Average Request RTT 26
2016-11-12 20:22:20.915 Detail, Expected callbackId was received
2016-11-12 20:22:20.915 Detail, Expected reply was received
2016-11-12 20:22:20.916 Detail, Message transaction complete
2016-11-12 20:22:20.916 Detail,
2016-11-12 20:22:20.916 Detail, Node002, Removing current message
2016-11-12 20:22:20.916 Detail,
2016-11-12 20:22:20.916 Info, Node002, Sending (Send) message (Callback ID=0x47, Expected Reply=0x04) - SwitchMultilevelCmd_Get (Node=2): 0x01, 0x09, 0x00, 0x13, 0x02, 0x02, 0x26, 0x02, 0x25, 0x47, 0xa3
2016-11-12 20:22:20.926 Detail, Node002, Received: 0x01, 0x04, 0x01, 0x13, 0x01, 0xe8
2016-11-12 20:22:20.926 Detail, Node002, ZW_SEND_DATA delivered to Z-Wave stack
2016-11-12 20:22:20.943 Detail, Node002, Received: 0x01, 0x07, 0x00, 0x13, 0x47, 0x00, 0x00, 0x02, 0xae
2016-11-12 20:22:20.943 Detail, Node002, ZW_SEND_DATA Request with callback ID 0x47 received (expected 0x47)
2016-11-12 20:22:20.943 Info, Node002, Request RTT 23 Average Request RTT 24
2016-11-12 20:22:20.943 Detail, Expected callbackId was received
2016-11-12 20:22:20.955 Detail, Node002, Received: 0x01, 0x09, 0x00, 0x04, 0x00, 0x02, 0x03, 0x26, 0x03, 0x63, 0xb5
2016-11-12 20:22:20.956 Detail,
2016-11-12 20:22:20.956 Info, Node002, Response RTT 35 Average Response RTT 36
2016-11-12 20:22:20.956 Info, Node002, Received SwitchMultiLevel report: level=99
2016-11-12 20:22:20.956 Detail, Node002, Refreshed Value: old value=99, new value=99, type=byte
2016-11-12 20:22:20.956 Detail, Node002, Changes to this value are not verified
2016-11-12 20:22:20.956 Detail, Node002, Expected reply and command class was received
2016-11-12 20:22:20.957 Detail, Node002, Message transaction complete
2016-11-12 20:22:20.957 Detail,
2016-11-12 20:22:20.957 Detail, Node002, Removing current message
2016-11-12 20:22:20.957 Detail, Node002, Notification: ValueChanged
2016-11-12 20:22:22.976 Detail, Node002, Received: 0x01, 0x09, 0x00, 0x04, 0x00, 0x02, 0x03, 0x26, 0x03, 0x63, 0xb5
2016-11-12 20:22:22.976 Detail,
2016-11-12 20:22:22.977 Info, Node002, Received SwitchMultiLevel report: level=99
2016-11-12 20:22:22.977 Detail, Node002, Refreshed Value: old value=99, new value=99, type=byte
2016-11-12 20:22:22.977 Detail, Node002, Changes to this value are not verified
2016-11-12 20:22:22.977 Detail, Node002, Notification: ValueChanged
2016-11-12 20:22:23.001 Detail, Node002, Received: 0x01, 0x0c, 0x00, 0x04, 0x00, 0x02, 0x06, 0x31, 0x05, 0x04, 0x22, 0x00, 0x00, 0xe1
2016-11-12 20:22:23.001 Detail,
2016-11-12 20:22:23.001 Info, Node002, Received SensorMultiLevel report from node 2, instance 1, Power: value=0.0W
2016-11-12 20:22:23.001 Detail, Node002, Refreshed Value: old value=0.0, new value=0.0, type=decimal
2016-11-12 20:22:23.001 Detail, Node002, Changes to this value are not verified
2016-11-12 20:22:23.002 Detail, Node002, Notification: ValueChanged
  ` > ****2:) Rollo oben (99) –> setze Wert 0 in Objekte --> Relais "klickt", Rollo fährt ganz runter, Wert geht auf 0**** `  

>! ````
2016-11-12 20:25:31.015 Info, Node002, SwitchMultilevel::Set - Setting to level 0
2016-11-12 20:25:31.015 Info, Node002,   Duration: Default
2016-11-12 20:25:31.015 Detail, Node002, Queuing (Send) SwitchMultilevelCmd_Set (Node=2): 0x01, 0x0b, 0x00, 0x13, 0x02, 0x04, 0x26, 0x01, 0x00, 0xff, 0x25, 0x48, 0x54
2016-11-12 20:25:31.015 Detail, Node002, Queuing (Send) SwitchMultilevelCmd_Get (Node=2): 0x01, 0x09, 0x00, 0x13, 0x02, 0x02, 0x26, 0x02, 0x25, 0x49, 0xad
2016-11-12 20:25:31.015 Detail, 
2016-11-12 20:25:31.016 Info, Node002, Sending (Send) message (Callback ID=0x48, Expected Reply=0x13) - SwitchMultilevelCmd_Set (Node=2): 0x01, 0x0b, 0x00, 0x13, 0x02, 0x04, 0x26, 0x01, 0x00, 0xff, 0x25, 0x48, 0x54
2016-11-12 20:25:31.025 Detail, Node002,   Received: 0x01, 0x04, 0x01, 0x13, 0x01, 0xe8
2016-11-12 20:25:31.025 Detail, Node002,   ZW_SEND_DATA delivered to Z-Wave stack
2016-11-12 20:25:31.042 Detail, Node002,   Received: 0x01, 0x07, 0x00, 0x13, 0x48, 0x00, 0x00, 0x02, 0xa1
2016-11-12 20:25:31.043 Detail, Node002,   ZW_SEND_DATA Request with callback ID 0x48 received (expected 0x48)
2016-11-12 20:25:31.043 Info, Node002, Request RTT 26 Average Request RTT 25
2016-11-12 20:25:31.043 Detail,   Expected callbackId was received
2016-11-12 20:25:31.043 Detail,   Expected reply was received
2016-11-12 20:25:31.043 Detail,   Message transaction complete
2016-11-12 20:25:31.043 Detail, 
2016-11-12 20:25:31.044 Detail, Node002, Removing current message
2016-11-12 20:25:31.044 Detail, 
2016-11-12 20:25:31.044 Info, Node002, Sending (Send) message (Callback ID=0x49, Expected Reply=0x04) - SwitchMultilevelCmd_Get (Node=2): 0x01, 0x09, 0x00, 0x13, 0x02, 0x02, 0x26, 0x02, 0x25, 0x49, 0xad
2016-11-12 20:25:31.057 Detail, Node002,   Received: 0x01, 0x04, 0x01, 0x13, 0x01, 0xe8
2016-11-12 20:25:31.058 Detail, Node002,   ZW_SEND_DATA delivered to Z-Wave stack
2016-11-12 20:25:31.071 Detail, Node002,   Received: 0x01, 0x07, 0x00, 0x13, 0x49, 0x00, 0x00, 0x02, 0xa0
2016-11-12 20:25:31.071 Detail, Node002,   ZW_SEND_DATA Request with callback ID 0x49 received (expected 0x49)
2016-11-12 20:25:31.071 Info, Node002, Request RTT 26 Average Request RTT 25
2016-11-12 20:25:31.071 Detail,   Expected callbackId was received
2016-11-12 20:25:31.080 Detail, Node002,   Received: 0x01, 0x09, 0x00, 0x04, 0x00, 0x02, 0x03, 0x26, 0x03, 0x63, 0xb5
2016-11-12 20:25:31.081 Detail, 
2016-11-12 20:25:31.081 Info, Node002, Response RTT 36 Average Response RTT 36
2016-11-12 20:25:31.081 Info, Node002, Received SwitchMultiLevel report: level=99
2016-11-12 20:25:31.081 Detail, Node002, Refreshed Value: old value=99, new value=99, type=byte
2016-11-12 20:25:31.081 Detail, Node002, Changes to this value are not verified
2016-11-12 20:25:31.081 Detail, Node002,   Expected reply and command class was received
2016-11-12 20:25:31.081 Detail, Node002,   Message transaction complete
2016-11-12 20:25:31.081 Detail, 
2016-11-12 20:25:31.081 Detail, Node002, Removing current message
2016-11-12 20:25:31.082 Detail, Node002, Notification: ValueChanged
2016-11-12 20:25:32.188 Detail, Node002,   Received: 0x01, 0x0c, 0x00, 0x04, 0x00, 0x02, 0x06, 0x31, 0x05, 0x04, 0x22, 0x04, 0xdd, 0x38
2016-11-12 20:25:32.188 Detail, 
2016-11-12 20:25:32.188 Info, Node002, Received SensorMultiLevel report from node 2, instance 1, Power: value=124.5W
2016-11-12 20:25:32.189 Detail, Node002, Refreshed Value: old value=0.0, new value=124.5, type=decimal
2016-11-12 20:25:32.189 Detail, Node002, Changes to this value are not verified
2016-11-12 20:25:32.189 Detail, Node002, Notification: ValueChanged
2016-11-12 20:25:47.501 Detail, Node002,   Received: 0x01, 0x0c, 0x00, 0x04, 0x00, 0x02, 0x06, 0x31, 0x05, 0x04, 0x22, 0x00, 0x00, 0xe1
2016-11-12 20:25:47.501 Detail, 
2016-11-12 20:25:47.502 Info, Node002, Received SensorMultiLevel report from node 2, instance 1, Power: value=0.0W
2016-11-12 20:25:47.502 Detail, Node002, Refreshed Value: old value=124.5, new value=0.0, type=decimal
2016-11-12 20:25:47.502 Detail, Node002, Changes to this value are not verified
2016-11-12 20:25:47.502 Detail, Node002, Notification: ValueChanged
2016-11-12 20:25:48.661 Detail, Node002,   Received: 0x01, 0x09, 0x00, 0x04, 0x00, 0x02, 0x03, 0x26, 0x03, 0x00, 0xd6
2016-11-12 20:25:48.661 Detail, 
2016-11-12 20:25:48.661 Info, Node002, Received SwitchMultiLevel report: level=0
2016-11-12 20:25:48.661 Detail, Node002, Refreshed Value: old value=99, new value=0, type=byte
2016-11-12 20:25:48.662 Detail, Node002, Changes to this value are not verified
2016-11-12 20:25:48.662 Detail, Node002, Notification: ValueChanged
2016-11-12 20:25:48.681 Detail, Node002,   Received: 0x01, 0x0c, 0x00, 0x04, 0x00, 0x02, 0x06, 0x31, 0x05, 0x04, 0x22, 0x00, 0x00, 0xe1
2016-11-12 20:25:48.681 Detail, 
2016-11-12 20:25:48.681 Info, Node002, Received SensorMultiLevel report from node 2, instance 1, Power: value=0.0W
2016-11-12 20:25:48.682 Detail, Node002, Refreshed Value: old value=0.0, new value=0.0, type=decimal
2016-11-12 20:25:48.682 Detail, Node002, Changes to this value are not verified
2016-11-12 20:25:48.682 Detail, Node002, Notification: ValueChanged
> ****3:) Rollo unten (0) –> setze Wert 50 in Objekte --> Relais "klickt", Rollo fährt ganz hoch, Wert geht auf 99****

! 2016-11-12 20:27:09.764 Info, Node002, SwitchMultilevel::Set - Setting to level 50 2016-11-12 20:27:09.764 Info, Node002, Duration: Default 2016-11-12 20:27:09.764 Detail, Node002, Queuing (Send) SwitchMultilevelCmd_Set (Node=2): 0x01, 0x0b, 0x00, 0x13, 0x02, 0x04, 0x26, 0x01, 0x32, 0xff, 0x25, 0x4a, 0x64 2016-11-12 20:27:09.764 Detail, Node002, Queuing (Send) SwitchMultilevelCmd_Get (Node=2): 0x01, 0x09, 0x00, 0x13, 0x02, 0x02, 0x26, 0x02, 0x25, 0x4b, 0xaf 2016-11-12 20:27:09.765 Detail, 2016-11-12 20:27:09.765 Info, Node002, Sending (Send) message (Callback ID=0x4a, Expected Reply=0x13) - SwitchMultilevelCmd_Set (Node=2): 0x01, 0x0b, 0x00, 0x13, 0x02, 0x04, 0x26, 0x01, 0x32, 0xff, 0x25, 0x4a, 0x64 2016-11-12 20:27:09.774 Detail, Node002, Received: 0x01, 0x04, 0x01, 0x13, 0x01, 0xe8 2016-11-12 20:27:09.774 Detail, Node002, ZW_SEND_DATA delivered to Z-Wave stack 2016-11-12 20:27:09.792 Detail, Node002, Received: 0x01, 0x07, 0x00, 0x13, 0x4a, 0x00, 0x00, 0x02, 0xa3 2016-11-12 20:27:09.792 Detail, Node002, ZW_SEND_DATA Request with callback ID 0x4a received (expected 0x4a) 2016-11-12 20:27:09.792 Info, Node002, Request RTT 26 Average Request RTT 25 2016-11-12 20:27:09.792 Detail, Expected callbackId was received 2016-11-12 20:27:09.792 Detail, Expected reply was received 2016-11-12 20:27:09.793 Detail, Message transaction complete 2016-11-12 20:27:09.793 Detail, 2016-11-12 20:27:09.793 Detail, Node002, Removing current message 2016-11-12 20:27:09.793 Detail, 2016-11-12 20:27:09.793 Info, Node002, Sending (Send) message (Callback ID=0x4b, Expected Reply=0x04) - SwitchMultilevelCmd_Get (Node=2): 0x01, 0x09, 0x00, 0x13, 0x02, 0x02, 0x26, 0x02, 0x25, 0x4b, 0xaf 2016-11-12 20:27:09.802 Detail, Node002, Received: 0x01, 0x04, 0x01, 0x13, 0x01, 0xe8 2016-11-12 20:27:09.802 Detail, Node002, ZW_SEND_DATA delivered to Z-Wave stack 2016-11-12 20:27:09.819 Detail, Node002, Received: 0x01, 0x07, 0x00, 0x13, 0x4b, 0x00, 0x00, 0x03, 0xa3 2016-11-12 20:27:09.819 Detail, Node002, ZW_SEND_DATA Request with callback ID 0x4b received (expected 0x4b) 2016-11-12 20:27:09.819 Info, Node002, Request RTT 25 Average Request RTT 25 2016-11-12 20:27:09.819 Detail, Expected callbackId was received 2016-11-12 20:27:09.833 Detail, Node002, Received: 0x01, 0x09, 0x00, 0x04, 0x00, 0x02, 0x03, 0x26, 0x03, 0x00, 0xd6 2016-11-12 20:27:09.833 Detail, 2016-11-12 20:27:09.834 Info, Node002, Response RTT 39 Average Response RTT 37 2016-11-12 20:27:09.834 Info, Node002, Received SwitchMultiLevel report: level=0 2016-11-12 20:27:09.834 Detail, Node002, Refreshed Value: old value=0, new value=0, type=byte 2016-11-12 20:27:09.834 Detail, Node002, Changes to this value are not verified 2016-11-12 20:27:09.834 Detail, Node002, Expected reply and command class was received 2016-11-12 20:27:09.834 Detail, Node002, Message transaction complete 2016-11-12 20:27:09.835 Detail, 2016-11-12 20:27:09.835 Detail, Node002, Removing current message 2016-11-12 20:27:09.835 Detail, Node002, Notification: ValueChanged 2016-11-12 20:27:10.937 Detail, Node002, Received: 0x01, 0x0c, 0x00, 0x04, 0x00, 0x02, 0x06, 0x31, 0x05, 0x04, 0x22, 0x04, 0xe6, 0x03 2016-11-12 20:27:10.938 Detail, 2016-11-12 20:27:10.938 Info, Node002, Received SensorMultiLevel report from node 2, instance 1, Power: value=125.4W 2016-11-12 20:27:10.938 Detail, Node002, Refreshed Value: old value=0.0, new value=125.4, type=decimal 2016-11-12 20:27:10.938 Detail, Node002, Changes to this value are not verified 2016-11-12 20:27:10.938 Detail, Node002, Notification: ValueChanged 2016-11-12 20:27:26.252 Detail, Node002, Received: 0x01, 0x0c, 0x00, 0x04, 0x00, 0x02, 0x06, 0x31, 0x05, 0x04, 0x22, 0x00, 0x00, 0xe1 2016-11-12 20:27:26.253 Detail, 2016-11-12 20:27:26.253 Info, Node002, Received SensorMultiLevel report from node 2, instance 1, Power: value=0.0W 2016-11-12 20:27:26.253 Detail, Node002, Refreshed Value: old value=125.4, new value=0.0, type=decimal 2016-11-12 20:27:26.253 Detail, Node002, Changes to this value are not verified 2016-11-12 20:27:26.253 Detail, Node002, Notification: ValueChanged 2016-11-12 20:27:27.583 Detail, Node002, Received: 0x01, 0x09, 0x00, 0x04, 0x00, 0x02, 0x03, 0x26, 0x03, 0x63, 0xb5 2016-11-12 20:27:27.584 Detail, 2016-11-12 20:27:27.584 Info, Node002, Received SwitchMultiLevel report: level=99 2016-11-12 20:27:27.584 Detail, Node002, Refreshed Value: old value=0, new value=99, type=byte 2016-11-12 20:27:27.584 Detail, Node002, Changes to this value are not verified 2016-11-12 20:27:27.585 Detail, Node002, Notification: ValueChanged 2016-11-12 20:27:27.602 Detail, Node002, Received: 0x01, 0x0c, 0x00, 0x04, 0x00, 0x02, 0x06, 0x31, 0x05, 0x04, 0x22, 0x00, 0x00, 0xe1 2016-11-12 20:27:27.603 Detail, 2016-11-12 20:27:27.603 Info, Node002, Received SensorMultiLevel report from node 2, instance 1, Power: value=0.0W 2016-11-12 20:27:27.603 Detail, Node002, Refreshed Value: old value=0.0, new value=0.0, type=decimal 2016-11-12 20:27:27.603 Detail, Node002, Changes to this value are not verified 2016-11-12 20:27:27.604 Detail, Node002, Notification: ValueChanged `
Wenn das tatsächlich die Meldungen aus OZW sind, dann meine Frage: geht das überhaupt?

So weit ich sehen kann, dass Kommando kommt schon an:
` > Info, Node002, SwitchMultilevel::Set - Setting to level 50

…

Info, Node002, Received SwitchMultiLevel report: level=99 `
Dein Gerät meldet 99 zurück auch nach 2 Sekunden.

Lenny.CB

~~@Bluefox:~~

So weit ich sehen kann, dass Kommando kommt schon an:
` > Info, Node002, SwitchMultilevel::Set - Setting to level 50

…

Info, Node002, Received SwitchMultiLevel report: level=99 Dein Gerät meldet 99 zurück auch nach 2 Sekunden.

und genau da ist das Problem. Ich denke das das Gerät "nur" unten oder oben kennt, bzw. 0 oder 99.

Vielleicht liegts auch an den Configurationseinstellungen beim Includieren.

Ich werde jetzt die Config in FHEM prüfen. Da hat es zumindest perfekt funktioniert. Mal schauen ob ich da ein OZW-Log rausbekomme.

Patrick

ich schaffe es leider auch nicht den Adapter zu installieren

bei mir kommt immer dieser Fehler

! ````
C:\Program Files\IO BROKER\ioBroker>npm install https://github.com/ioBroker/ioBroker.zwave/tarball/master --production
|
iobroker.zwave@0.4.2 preinstall C:\Program Files\IO BROKER\ioBroker\node_modules\iobroker.zwave
node preinstall.js
! win32 is currently not supported

openzwave-shared@1.2.0 preinstall C:\Program Files\IO BROKER\ioBroker\node_modules\iobroker.zwave\node_modules\openzwave-shared
node lib/install-ozw.js
! Installing Open Z-Wave
Installing dependencies to C:\Users\rickfl\AppData\Local\Temp\ozwinstall-9bksiu4ygb9
npm WARN deprecated wrench@1.5.9: wrench.js is deprecated! You should check out fs-extra (https://github.com/jprichardson/node-fs-extra) for any operations you were using wrench for. Thanks for all the usage over the years.
module.js:327
throw err;
^
! Error: Cannot find module 'C:\Users\rickfl\AppData\Local\Temp\ozwinstall-9bksiu4ygb9/node_modules/request'
at Function.Module._resolveFilename (module.js:325:15)
at Function.Module._load (module.js:276:25)
at Module.require (module.js:353:17)
at require (internal/module.js:12:17)
at Module.module.exports (C:\Program Files\IO BROKER\ioBroker\node_modules\iobroker.zwave\node_modules\openzwave-shared\lib\install-ozw.js:165:13)
at Object. <anonymous>(C:\Program Files\IO BROKER\ioBroker\node_modules\iobroker.zwave\node_modules\openzwave-shared\lib\install-ozw.js:220:12)
at Module._compile (module.js:409:26)
at Object.Module._extensions..js (module.js:416:10)
at Module.load (module.js:343:32)
at Function.Module._load (module.js:300:12)
npm ERR! Windows_NT 10.0.10586
npm ERR! argv "C:\Program Files\nodejs\node.exe" "C:\Program Files\nodejs\node_modules\npm\bin\npm-cli.js" "install" "https://github.com/ioBroker/ioBroker.zwave/tarball/master" "--production"
npm ERR! node v4.6.1
npm ERR! npm v2.15.9
npm ERR! code ELIFECYCLE
! npm ERR! openzwave-shared@1.2.0 preinstall: node lib/install-ozw.js
npm ERR! Exit status 1
npm ERR!
npm ERR! Failed at the openzwave-shared@1.2.0 preinstall script 'node lib/install-ozw.js'.
npm ERR! This is most likely a problem with the openzwave-shared package,
npm ERR! not with npm itself.
npm ERR! Tell the author that this fails on your system:
npm ERR! node lib/install-ozw.js
npm ERR! You can get information on how to open an issue for this project with:
npm ERR! npm bugs openzwave-shared
npm ERR! Or if that isn't available, you can get their info via:
npm ERR!
npm ERR! npm owner ls openzwave-shared
npm ERR! There is likely additional logging output above.
! npm ERR! Please include the following file with any support request:
npm ERR! C:\Program Files\IO BROKER\ioBroker\npm-debug.log
! C:\Program Files\IO BROKER\ioBroker></anonymous>

Bluefox

> win32 is currently not supported
Hm

Patrick

~~@Bluefox:~~

> win32 is currently not supported
Hm `

das Komische ist das ich es schon mal geschafft habe den Adapter zu installieren nach dem er aber nicht gestartet ist und den USB Stick nicht angezeigt hat habe ich ihn neu installieren wollen

Lenny.CB

~~@Bluefox:~~

` > Info, Node002, SwitchMultilevel::Set - Setting to level 50

…

Info, Node002, Received SwitchMultiLevel report: level=99 Dein Gerät meldet 99 zurück auch nach 2 Sekunden.
Problem ist gelößt. ich hatte nun mal den Parameter 29 auf "Start calibration process(1)" gesetzt. Danach wurden alle Befehle zwischen 0 und 99 korrekt angenommen und verarbeitet.

Ich bin immer davon ausgegangen, dass die Kalibrierung nur einmalig nach der Installation der Module erfolgen muss.

Bluefox

~~@Lenny.CB:~~

~~@Bluefox:~~

` > Info, Node002, SwitchMultilevel::Set - Setting to level 50

…

Info, Node002, Received SwitchMultiLevel report: level=99 Dein Gerät meldet 99 zurück auch nach 2 Sekunden.
Problem ist gelößt. ich hatte nun mal den Parameter 29 auf "Start calibration process(1)" gesetzt. Danach wurden alle Befehle zwischen 0 und 99 korrekt angenommen und verarbeitet.

Ich bin immer davon ausgegangen, dass die Kalibrierung nur einmalig nach der Installation der Module erfolgen muss. `
Hast du die Kalibrierung über iob gestartet?

Oder braucht man dafür extra Tool?

Lenny.CB

~~@Bluefox:~~

Hast du die Kalibrierung über iob gestartet?

Oder braucht man dafür extra Tool? `
habe das über ioB gemacht. In den Objekten –> zwave.0 --> NODE2 --> CONFIGURATION den Parameter 29 (Forced_Roller_Shutter_calibration) gesetzt, Rollo fährt hoch-runter-hoch... fertig...

im Bild ist Default(0) = "normalmodus" und (1) ist Kalibrierung

Danach ging alles prima…

Bluefox

Heisst es Ich kann Adapter veröffentlichen?

Lenny.CB

~~@Bluefox:~~

Heisst es Ich kann Adapter veröffentlichen? `
also was ich testen konnte ist soweit jetzt auch ok. Das Aoetec EnergyMeter hate ab der Version 0.4.1 auch alle Kanäle.

Nur mit der Configuration stelle ich mich noch etwas "dusselig" an, aber das wird auch noch.

also mein "GO" hast du…

was sagen die anderen zwave Nutzer?

OstfrieseUnterwegs

~~@Bluefox:~~

Heisst es Ich kann Adapter veröffentlichen? `

Funktioniert bei mir OK.

Ich habe ja das Problem, dass alles, was über eine Drop-Down-Liste im Reiter 'Objekte' nicht gesetzt werden kann.

Allerdings per

setState("zwave.0.NODE5.CONFIGURATION.Tamper_operating_modes"/*Tamper operating modes*/, 2, true);

funktioniert das einwandfrei.

Dutchman

~~@Bluefox:~~

Heisst es Ich kann Adapter veröffentlichen? `

Was ich bis jetzt testen konnte läuft, habe noch ein par Geräte liegen nur im Moment zu wenig Zeit ;(

Stabiel ja, Installation Fehler = thread durchlesen

Sent from my iPhone using Tapatalk

AlCalzone

Falls du noch nicht veröffentlich hast, dann probiere ich mich nachher noch an der Greenwave-Dose und gebe Feedback.

~~@OstfrieseUnterwegs:~~

Ich habe ja das Problem, dass alles, was über eine Drop-Down-Liste im Reiter 'Objekte' nicht gesetzt werden kann. `
Seltsam… Bei mir geht das. Mein Aeotec-Sensor hat einige Parameter mit Dropdowns im Objekte-Reiter, die er einwandfrei annimmt.

~~@OstfrieseUnterwegs:~~

Allerdings per
setState("zwave.0.NODE5.CONFIGURATION.Tamper_operating_modes"/*Tamper operating modes*/, 2, true);
funktioniert das einwandfrei. `
Bist du dir sicher, dass die Parameter so auch bei deinem Gerät ankommen? ACK=true bedeutet eigentlich, dass der Adapter keinen Finger mehr rührt, weil er davon ausgeht, dass die Änderungen schon bearbeitet sind.

OstfrieseUnterwegs

~~@AlCalzone:~~

Bist du dir sicher, dass die Parameter so auch bei deinem Gerät ankommen? ACK=true bedeutet eigentlich, dass der Adapter keinen Finger mehr rührt, weil er davon ausgeht, dass die Änderungen schon bearbeitet sind. `

:lol: Frisch behauptet ist halb bewiesen

Im Objekte Tab steht's wenigstens auf schwarz - im Gegensatz zu denen, die ich direkt im Objekte Tab umschalte - die bleiben rot. Ich prüfe das die Tage nochmal im OZW Logfile. Bin im Moment auf Reisen.

AlCalzone

@Bluefox:

Habe die Greenwave-Dose eingebunden. Beim Einbinden gab es keine Probleme, die Dose ließ ich aber bis zum Neustart des zWave-Adapters nicht schalten.

Vielleicht war ich aber auch zu ungeduldig, beim zweiten Versuch hats dann auf Anhieb geklappt.

Hier noch der ioBroker-Log beim Einbinden. Zwischendurch sieht man die zuvor erwähnten remove-value-Befehle während des Einbindens… keine Ahnung was das soll.

! 2016-11-21 16:25:44.019 - info: zwave.0 Execute addNode 2016-11-21 16:25:44.025 - info: zwave.0 controller command feedback: state: "The command is starting", error: "No error", helpmsg: "ControllerCommand - Starting" 2016-11-21 16:25:44.027 - info: zwave.0 controller command feedback: state: "Controller is waiting for a user action", error: "No error", helpmsg: "ControllerCommand - Waiting" 2016-11-21 16:25:51.419 - info: zwave.0 controller command feedback: state: "The controller is communicating with the other device to carry out the command", error: "No error", helpmsg: "ControllerCommand - InProgress" 2016-11-21 16:25:51.572 - info: zwave.0 controller command feedback: state: "The controller is communicating with the other device to carry out the command", error: "No error", helpmsg: "ControllerCommand - InProgress" 2016-11-21 16:25:51.928 - info: zwave.0 controller command feedback: state: "The controller is communicating with the other device to carry out the command", error: "No error", helpmsg: "ControllerCommand - InProgress" 2016-11-21 16:25:51.980 - info: zwave.0 Create new device: zwave.0.NODE4[] 2016-11-21 16:25:51.985 - info: zwave.0 Channel created: zwave.0.NODE4.SWITCH_BINARY = false, index = 0, comClass = 37, instance = 1 2016-11-21 16:25:51.987 - info: zwave.0 State created: zwave.0.NODE4.SWITCH_BINARY.Switch_1 = undefined, index = 0, comClass = 37, instance = 1 2016-11-21 16:25:51.990 - info: zwave.0 Channel created: zwave.0.NODE4.SWITCH_ALL = Disabled, index = 0, comClass = 39, instance = 1 2016-11-21 16:25:51.994 - info: zwave.0 State created: zwave.0.NODE4.SWITCH_ALL.Switch_All = undefined, index = 0, comClass = 39, instance = 1 2016-11-21 16:25:51.997 - info: zwave.0 Channel created: zwave.0.NODE4.METER = 0.0, index = 0, comClass = 50, instance = 1 2016-11-21 16:25:51.999 - info: zwave.0 State created: zwave.0.NODE4.METER.Unknown_1 = undefined, index = 0, comClass = 50, instance = 1 2016-11-21 16:25:52.001 - info: zwave.0 Channel created: zwave.0.NODE4.VERSION = Unknown, index = 0, comClass = 134, instance = 1 2016-11-21 16:25:52.002 - info: zwave.0 State created: zwave.0.NODE4.VERSION.Library_Version = undefined, index = 0, comClass = 134, instance = 1 2016-11-21 16:25:52.004 - info: zwave.0 Channel created: zwave.0.NODE4.VERSION = Unknown, index = 1, comClass = 134, instance = 1 2016-11-21 16:25:52.005 - info: zwave.0 State created: zwave.0.NODE4.VERSION.Protocol_Version = undefined, index = 1, comClass = 134, instance = 1 2016-11-21 16:25:52.006 - info: zwave.0 Channel created: zwave.0.NODE4.VERSION = Unknown, index = 2, comClass = 134, instance = 1 2016-11-21 16:25:52.007 - info: zwave.0 State created: zwave.0.NODE4.VERSION.Application_Version = undefined, index = 2, comClass = 134, instance = 1 2016-11-21 16:25:52.021 - info: zwave.0 Channel created: zwave.0.NODE4.ALARM = 0, index = 0, comClass = 113, instance = 1 2016-11-21 16:25:52.023 - info: zwave.0 State created: zwave.0.NODE4.ALARM.Alarm_Type_1 = undefined, index = 0, comClass = 113, instance = 1 2016-11-21 16:25:52.026 - info: zwave.0 Channel created: zwave.0.NODE4.ALARM = 0, index = 1, comClass = 113, instance = 1 2016-11-21 16:25:52.028 - info: zwave.0 State created: zwave.0.NODE4.ALARM.Alarm_Level_1 = undefined, index = 1, comClass = 113, instance = 1 2016-11-21 16:25:52.032 - info: zwave.0 Channel created: zwave.0.NODE4.INDICATOR = 0, index = 0, comClass = 135, instance = 1 2016-11-21 16:25:52.035 - info: zwave.0 State created: zwave.0.NODE4.INDICATOR.Indicator_1 = undefined, index = 0, comClass = 135, instance = 1 2016-11-21 16:25:52.037 - info: zwave.0 Channel created: zwave.0.NODE4.PROTECTION = Unprotected, index = 0, comClass = 117, instance = 1 2016-11-21 16:25:52.039 - info: zwave.0 State created: zwave.0.NODE4.PROTECTION.Protection = undefined, index = 0, comClass = 117, instance = 1 2016-11-21 16:25:52.040 - info: zwave.0 controller command feedback: state: "The command has completed successfully", error: "No error", helpmsg: "ControllerCommand - Completed" 2016-11-21 16:25:52.178 - info: zwave.0 Update zwave.0.NODE4 2016-11-21 16:25:52.189 - info: zwave.0 Channel created: zwave.0.NODE4.CONFIGURATION = 10, index = 0, comClass = 112, instance = 1 2016-11-21 16:25:52.193 - info: zwave.0 State created: zwave.0.NODE4.CONFIGURATION.Power_delta = undefined, index = 0, comClass = 112, instance = 1 2016-11-21 16:25:52.196 - info: zwave.0 Channel created: zwave.0.NODE4.CONFIGURATION = 2, index = 1, comClass = 112, instance = 1 2016-11-21 16:25:52.198 - info: zwave.0 State created: zwave.0.NODE4.CONFIGURATION.No_communication_light = undefined, index = 1, comClass = 112, instance = 1 2016-11-21 16:25:52.200 - info: zwave.0 Channel created: zwave.0.NODE4.CONFIGURATION = Black (empty), index = 2, comClass = 112, instance = 1 2016-11-21 16:25:52.203 - info: zwave.0 State created: zwave.0.NODE4.CONFIGURATION.Room_color = undefined, index = 2, comClass = 112, instance = 1 2016-11-21 16:25:52.206 - info: zwave.0 Channel created: zwave.0.NODE4.CONFIGURATION = All ON, index = 3, comClass = 112, instance = 1 2016-11-21 16:25:52.208 - info: zwave.0 State created: zwave.0.NODE4.CONFIGURATION.Power_on_relay = undefined, index = 3, comClass = 112, instance = 1 2016-11-21 16:25:52.211 - info: zwave.0 Channel created: zwave.0.NODE4.CONFIGURATION = Enable, index = 4, comClass = 112, instance = 1 2016-11-21 16:25:52.213 - info: zwave.0 State created: zwave.0.NODE4.CONFIGURATION.LED_on_network_error = undefined, index = 4, comClass = 112, instance = 1 2016-11-21 16:25:52.216 - info: zwave.0 value removed: 4 comClass: 113 instance 1 value: 0 2016-11-21 16:25:52.220 - info: zwave.0 value removed: 4 comClass: 113 instance 1 value: 1 2016-11-21 16:25:52.223 - info: zwave.0 value removed: 4 comClass: 135 instance 1 value: 0 2016-11-21 16:25:52.258 - info: zwave.0 State created: zwave.0.NODE4.METER.Power_1 = undefined, index = 8, comClass = 50, instance = 1 2016-11-21 16:25:52.263 - info: zwave.0 State created: zwave.0.NODE4.METER.Exporting_1 = undefined, index = 32, comClass = 50, instance = 1 2016-11-21 16:25:52.277 - info: zwave.0 State created: zwave.0.NODE4.METER.Reset = undefined, index = 33, comClass = 50, instance = 1 2016-11-21 16:25:52.620 - info: zwave.0 controller command feedback: state: "The command is starting", error: "No error", helpmsg: "ControllerCommand - Starting" 2016-11-21 16:25:52.625 - info: zwave.0 controller command feedback: state: "The controller is communicating with the other device to carry out the command", error: "No error", helpmsg: "ControllerCommand - InProgress" 2016-11-21 16:25:52.684 - info: zwave.0 controller command feedback: state: "The command has completed successfully", error: "No error", helpmsg: "ControllerCommand - Completed" 2016-11-21 16:25:52.687 - info: zwave.0 controller command feedback: state: "The command is starting", error: "No error", helpmsg: "ControllerCommand - Starting" 2016-11-21 16:25:52.692 - info: zwave.0 controller command feedback: state: "The controller is communicating with the other device to carry out the command", error: "No error", helpmsg: "ControllerCommand - InProgress" 2016-11-21 16:25:53.315 - info: zwave.0 controller command feedback: state: "The command has completed successfully", error: "No error", helpmsg: "ControllerCommand - Completed" 2016-11-21 16:25:53.401 - info: zwave.0 Channel created: zwave.0.NODE4.SWITCH_ALL = On and Off Enabled, index = 0, comClass = 39, instance = 1 2016-11-21 16:25:53.404 - info: zwave.0 State created: zwave.0.NODE4.SWITCH_ALL.Switch_All = undefined, index = 0, comClass = 39, instance = 1 2016-11-21 16:25:53.440 - info: zwave.0 Channel created: zwave.0.NODE4.PROTECTION = Unprotected, index = 0, comClass = 117, instance = 1 2016-11-21 16:25:53.443 - info: zwave.0 State created: zwave.0.NODE4.PROTECTION.Protection = undefined, index = 0, comClass = 117, instance = 1 2016-11-21 16:25:53.465 - info: zwave.0 Channel created: zwave.0.NODE4.SWITCH_BINARY = true, index = 0, comClass = 37, instance = 1 2016-11-21 16:25:53.468 - info: zwave.0 State created: zwave.0.NODE4.SWITCH_BINARY.Switch_1 = undefined, index = 0, comClass = 37, instance = 1 2016-11-21 16:25:53.498 - info: zwave.0 Channel created: zwave.0.NODE4.METER = false, index = 32, comClass = 50, instance = 1 2016-11-21 16:25:53.504 - info: zwave.0 Channel created: zwave.0.NODE4.METER = 0.0000, index = 0, comClass = 50, instance = 1 2016-11-21 16:25:53.506 - info: zwave.0 State created: zwave.0.NODE4.METER.Energy_1 = undefined, index = 0, comClass = 50, instance = 1 2016-11-21 16:25:53.508 - info: zwave.0 Channel created: zwave.0.NODE4.METER = 0.0000, index = 1, comClass = 50, instance = 1 2016-11-21 16:25:53.510 - info: zwave.0 State created: zwave.0.NODE4.METER.Previous_Reading_1 = undefined, index = 1, comClass = 50, instance = 1 2016-11-21 16:25:53.513 - info: zwave.0 Channel created: zwave.0.NODE4.METER = 0.0000, index = 1, comClass = 50, instance = 1 2016-11-21 16:25:53.516 - info: zwave.0 State created: zwave.0.NODE4.METER.Previous_Reading_1 = undefined, index = 1, comClass = 50, instance = 1 2016-11-21 16:25:53.520 - info: zwave.0 Channel created: zwave.0.NODE4.METER = 1, index = 2, comClass = 50, instance = 1 2016-11-21 16:25:53.524 - info: zwave.0 State created: zwave.0.NODE4.METER.Interval_1 = undefined, index = 2, comClass = 50, instance = 1 2016-11-21 16:25:53.529 - info: zwave.0 Channel created: zwave.0.NODE4.METER = 1, index = 2, comClass = 50, instance = 1 2016-11-21 16:25:53.531 - info: zwave.0 State created: zwave.0.NODE4.METER.Interval_1 = undefined, index = 2, comClass = 50, instance = 1 2016-11-21 16:25:53.543 - info: zwave.0 Channel created: zwave.0.NODE4.METER = false, index = 32, comClass = 50, instance = 1 2016-11-21 16:25:53.548 - info: zwave.0 Channel created: zwave.0.NODE4.METER = 0.0, index = 8, comClass = 50, instance = 1 2016-11-21 16:25:53.552 - info: zwave.0 Channel created: zwave.0.NODE4.METER = 0.0, index = 9, comClass = 50, instance = 1 2016-11-21 16:25:53.554 - info: zwave.0 State created: zwave.0.NODE4.METER.Previous_Reading_1 = undefined, index = 9, comClass = 50, instance = 1 2016-11-21 16:25:53.556 - info: zwave.0 Channel created: zwave.0.NODE4.METER = 0.0, index = 9, comClass = 50, instance = 1 2016-11-21 16:25:53.558 - info: zwave.0 State created: zwave.0.NODE4.METER.Previous_Reading_1 = undefined, index = 9, comClass = 50, instance = 1 2016-11-21 16:25:53.560 - info: zwave.0 Channel created: zwave.0.NODE4.METER = 1, index = 10, comClass = 50, instance = 1 2016-11-21 16:25:53.562 - info: zwave.0 State created: zwave.0.NODE4.METER.Interval_1 = undefined, index = 10, comClass = 50, instance = 1 2016-11-21 16:25:53.566 - info: zwave.0 Channel created: zwave.0.NODE4.METER = 1, index = 10, comClass = 50, instance = 1 2016-11-21 16:25:53.569 - info: zwave.0 State created: zwave.0.NODE4.METER.Interval_1 = undefined, index = 10, comClass = 50, instance = 1 2016-11-21 16:25:53.572 - info: zwave.0 node ready nodeID: 4, nodeInfo: {"manufacturer":"GreenWave","manufacturerid":"0x0099","product":"PowerNode 1 port","producttype":"0x0002","productid":"0x0002","type":"Binary Power Switch","name":"","loc":""} 2016-11-21 16:25:53.574 - info: zwave.0 Create new device: zwave.0.NODE4[GreenWave PowerNode 1 port] !

Von meiner Seite scheint dann alles zu funktionieren.

–-

EDIT:

In der Dokumentation steht, dass nach abgeschlossenem Scan das Objekt "zwave.0.completed" zu "true" gesetzt wird. Im Code wird allerdings "forceInit" auf "false" gesetzt (Zeile 771):

adapter.setState('forceInit', false, true);

Patrick

~~@Patrick:~~

ich schaffe es leider auch nicht den Adapter zu installieren

bei mir kommt immer dieser Fehler

! C:\Program Files\IO BROKER\ioBroker>npm install https://github.com/ioBroker/ioBroker.zw … all/master --production
! |
! > iobroker.zwave@0.4.2 preinstall C:\Program Files\IO BROKER\ioBroker\node_modules\iobroker.zwave
! > node preinstall.js
! win32 is currently not supported
!
! > openzwave-shared@1.2.0 preinstall C:\Program Files\IO BROKER\ioBroker\node_modules\iobroker.zwave\node_modules\openzwave-shared
! > node lib/install-ozw.js
! Installing Open Z-Wave
! Installing dependencies to C:\Users\rickfl\AppData\Local\Temp\ozwinstall-9bksiu4ygb9
! npm WARN deprecated wrench@1.5.9: wrench.js is deprecated! You should check out fs-extra (https://github.com/jprichardson/node-fs-extra) for any operations you were using wrench for. Thanks for all the usage over the years.
! module.js:327
! throw err;
! ^
! Error: Cannot find module 'C:\Users\rickfl\AppData\Local\Temp\ozwinstall-9bksiu4ygb9/node_modules/request'
! at Function.Module._resolveFilename (module.js:325:15)
! at Function.Module._load (module.js:276:25)
! at Module.require (module.js:353:17)
! at require (internal/module.js:12:17)
! at Module.module.exports (C:\Program Files\IO BROKER\ioBroker\node_modules\iobroker.zwave\node_modules\openzwave-shared\lib\install-ozw.js:165:13)
! at Object. <anonymous>(C:\Program Files\IO BROKER\ioBroker\node_modules\iobroker.zwave\node_modules\openzwave-shared\lib\install-ozw.js:220:12)
! at Module._compile (module.js:409:26)
! at Object.Module._extensions..js (module.js:416:10)
! at Module.load (module.js:343:32)
! at Function.Module._load (module.js:300:12)
! npm ERR! Windows_NT 10.0.10586
! npm ERR! argv "C:\Program Files\nodejs\node.exe" "C:\Program Files\nodejs\node_modules\npm\bin\npm-cli.js" "install" "https://github.com/ioBroker/ioBroker.zw ... all/master" "--production"
! npm ERR! node v4.6.1
! npm ERR! npm v2.15.9
! npm ERR! code ELIFECYCLE
! npm ERR! openzwave-shared@1.2.0 preinstall: node lib/install-ozw.js
! npm ERR! Exit status 1
! npm ERR!
! npm ERR! Failed at the openzwave-shared@1.2.0 preinstall script 'node lib/install-ozw.js'.
! npm ERR! This is most likely a problem with the openzwave-shared package,
! npm ERR! not with npm itself.
! npm ERR! Tell the author that this fails on your system:
! npm ERR! node lib/install-ozw.js
! npm ERR! You can get information on how to open an issue for this project with:
! npm ERR! npm bugs openzwave-shared
! npm ERR! Or if that isn't available, you can get their info via:
! npm ERR!
! npm ERR! npm owner ls openzwave-shared
! npm ERR! There is likely additional logging output above.
! npm ERR! Please include the following file with any support request:
! npm ERR! C:\Program Files\IO BROKER\ioBroker\npm-debug.log
! C:\Program Files\IO BROKER\ioBroker></anonymous> `

hat hier für schon jemand einen Ansatz an was es liegen könnte

NEWS

Zwave 0.4

Support us

829
Online

31.7k
Users

79.8k
Topics

1.3m
Posts

NEWS

Zwave 0.4

Support us

829Online

31.7kUsers

79.8kTopics

1.3mPosts

829
Online

31.7k
Users

79.8k
Topics

1.3m
Posts