Smartmeter Elster AS1440
-
@homoran said in Smartmeter Elster AS1440:
@petlaw sagte in Smartmeter Elster AS1440:
groups iobroker
kein sudo?
Sollte er die haben ? Wurde bei der installation nicht vergeben.
peter@SMARTY:~$ sudo usermod -aG sudo iobroker [sudo] password for peter: peter@SMARTY:~$ sudo groups iobroker iobroker : iobroker tty dialout sudo audio video bluetooth peter@SMARTY:~$ sudo iobroker restart2023-05-11 11:30:38.783 - debug: smartmeter.0 (8047) CREATE SERIALPORT: 300 7 1 even 2023-05-11 11:30:38.785 - debug: smartmeter.0 (8047) SERIALPORT OPEN 2023-05-11 11:30:38.787 - debug: smartmeter.0 (8047) SET MESSAGE TIMEOUT TIMER: 30000 2023-05-11 11:31:08.788 - debug: smartmeter.0 (8047) MESSAGE TIMEOUT TRIGGERED 2023-05-11 11:31:08.789 - debug: smartmeter.0 (8047) Error: No or too long answer from Serial Device after last request. 2023-05-11 11:31:08.789 - warn: smartmeter.0 (8047) No or too long answer from Serial Device after last request. 2023-05-11 11:31:08.789 - debug: smartmeter.0 (8047) Error: No or too long answer from Serial Device after last request. 2023-05-11 11:31:08.790 - debug: smartmeter.0 (8047) Transport Reset!! Restart = true 2023-05-11 11:31:08.792 - debug: smartmeter.0 (8047) SERIALPORT CLOSE 2023-05-11 11:31:08.793 - debug: smartmeter.0 (8047) SCHEDULE NEXT RUN IN 30s -
Es sieht halt absolut nicht danach aus, als würde er die serielle Schnittstelle wirklich aufmachen und da etwas senden.
Zu keinem Zeitpunkt blinkt da am Lesekopf irgendwas.Gibts evt. irgendeine andere Möglichkeit, das zu checken ? Ich hätte mir da vom DEBUG mehr Information erwartet.
Auch wenn man auf SILLY stellt kommt nichts erhellendes dabei raus. -
@petlaw sagte in Smartmeter Elster AS1440:
Sollte er die haben ? Wurde bei der installation nicht vergeben.
Nein, sollte er nicht.
Mach das wieder rückgängig. -
@thomas-braun said in Smartmeter Elster AS1440:
@petlaw sagte in Smartmeter Elster AS1440:
Sollte er die haben ? Wurde bei der installation nicht vergeben.
Nein, sollte er nicht.
Mach das wieder rückgängig.Ist raus
peter@SMARTY:~$ sudo gpasswd -d iobroker sudo Removing user iobroker from group sudo peter@SMARTY:~$ sudo iobroker restart -
@petlaw sagte in Smartmeter Elster AS1440:
sudo iobroker restart
Und pack niemals das Kommando 'iobroker' zusammen mit 'sudo' an.
iob stop iob fix iob start iob diagAusgaben von
iob diagbitte posten. -
@thomas-braun said in Smartmeter Elster AS1440:
@petlaw sagte in Smartmeter Elster AS1440:
sudo iobroker restart
Und pack niemals das Kommando 'iobroker' zusammen mit 'sudo' an.
Sir, jawohl, Sir
iob stop iob fix iob start iob diagAusgaben von
iob diagbitte posten.======================= SUMMARY ======================= v.2023-04-16 Operatingsystem: Debian GNU/Linux 11 (bullseye) Kernel: 5.10.0-22-amd64 Installation: Native Timezone: Europe/Berlin (CEST, +0200) User-ID: 1000 X-Server: true Boot Target: graphical.target Pending OS-Updates: 2 Pending iob updates: 0 Nodejs-Installation: /usr/bin/nodejs v18.16.0 /usr/bin/node v18.16.0 /usr/bin/npm 9.5.1 /usr/bin/npx 9.5.1 Recommended versions are nodejs 18.x.y and npm 9.x.y Your nodejs installation is correct MEMORY: total used free shared buff/cache available Mem: 7.8G 1.2G 5.3G 8.0M 1.3G 6.4G Swap: 975M 0B 975M Total: 8.8G 1.2G 6.3G Active iob-Instances: 11 Active repo(s): stable ioBroker Core: js-controller 4.0.24 admin 6.3.5 ioBroker Status: iobroker is running on this host. Objects type: jsonl States type: jsonl Status admin and web instance: + system.adapter.admin.0 : admin : SMARTY - enabled, port: 8081, bind: 0.0.0.0, run as: admin + system.adapter.web.0 : web : SMARTY - enabled, port: 8082, bind: 0.0.0.0, run as: admin Objects: 481 States: 378 Size of iob-Database: 3.8M /opt/iobroker/iobroker-data/objects.jsonl 172K /opt/iobroker/iobroker-data/states.jsonl =================== END OF SUMMARY ====================Details:
======== Start marking the full check here ========= Skript v.2023-04-16 *** BASE SYSTEM *** Architecture : x86_64 Docker : false Virtualization : none Distributor ID: Debian Description: Debian GNU/Linux 11 (bullseye) Release: 11 Codename: bullseye PRETTY_NAME="Debian GNU/Linux 11 (bullseye)" NAME="Debian GNU/Linux" VERSION_ID="11" VERSION="11 (bullseye)" VERSION_CODENAME=bullseye ID=debian HOME_URL="https://www.debian.org/" SUPPORT_URL="https://www.debian.org/support" BUG_REPORT_URL="https://bugs.debian.org/" Systemuptime and Load: 11:50:00 up 8:57, 2 users, load average: 0.04, 0.09, 0.05 CPU threads: 4 *** Time and Time Zones *** Local time: Thu 2023-05-11 11:50:00 CEST Universal time: Thu 2023-05-11 09:50:00 UTC RTC time: Thu 2023-05-11 09:50:00 Time zone: Europe/Berlin (CEST, +0200) System clock synchronized: yes NTP service: active RTC in local TZ: no *** User and Groups *** peter /home/peter peter cdrom floppy sudo audio dip video plugdev netdev bluetooth lpadmin scanner iobroker *** X-Server-Setup *** X-Server: true Desktop: Terminal: tty Boot Target: graphical.target *** MEMORY *** total used free shared buff/cache available Mem: 7.8G 1.2G 5.3G 8.0M 1.3G 6.4G Swap: 975M 0B 975M Total: 8.8G 1.2G 6.3G 7828 M total memory 1170 M used memory 581 M active memory 1605 M inactive memory 5318 M free memory 164 M buffer memory 1175 M swap cache 975 M total swap 0 M used swap 975 M free swap *** FILESYSTEM *** Filesystem Type Size Used Avail Use% Mounted on udev devtmpfs 3.8G 0 3.8G 0% /dev tmpfs tmpfs 783M 1.5M 782M 1% /run /dev/mapper/SMARTY--vg-root ext4 23G 5.2G 17G 24% / tmpfs tmpfs 3.9G 0 3.9G 0% /dev/shm tmpfs tmpfs 5.0M 4.0K 5.0M 1% /run/lock /dev/sda2 ext2 471M 63M 384M 15% /boot /dev/mapper/SMARTY--vg-tmp ext4 1.8G 100K 1.7G 1% /tmp /dev/mapper/SMARTY--vg-var ext4 9.1G 752M 7.9G 9% /var /dev/mapper/SMARTY--vg-home ext4 198G 411M 188G 1% /home /dev/sda1 vfat 511M 5.8M 506M 2% /boot/efi tmpfs tmpfs 783M 64K 783M 1% /run/user/116 tmpfs tmpfs 783M 56K 783M 1% /run/user/1000 Messages concerning ext4 filesystem in dmesg: [Thu May 11 02:52:34 2023] EXT4-fs (dm-0): mounted filesystem with ordered data mode. Opts: (null) [Thu May 11 02:52:34 2023] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro [Thu May 11 02:52:35 2023] EXT4-fs (sda2): mounting ext2 file system using the ext4 subsystem [Thu May 11 02:52:35 2023] EXT4-fs (sda2): mounted filesystem without journal. Opts: (null) [Thu May 11 02:52:35 2023] EXT4-fs (dm-3): mounted filesystem with ordered data mode. Opts: (null) [Thu May 11 02:52:35 2023] EXT4-fs (dm-1): mounted filesystem with ordered data mode. Opts: (null) [Thu May 11 02:52:35 2023] EXT4-fs (dm-4): mounted filesystem with ordered data mode. Opts: (null) Show mounted filesystems (real ones only): TARGET SOURCE FSTYPE OPTIONS / /dev/mapper/SMARTY--vg-root ext4 rw,relatime,errors=remount-ro |-/boot /dev/sda2 ext2 rw,relatime | `-/boot/efi /dev/sda1 vfat rw,relatime,fmask=0077,dmask=0077,codepage=437,iocharset=ascii,shortname=mixed,utf8,errors=remount-ro |-/tmp /dev/mapper/SMARTY--vg-tmp ext4 rw,relatime |-/var /dev/mapper/SMARTY--vg-var ext4 rw,relatime `-/home /dev/mapper/SMARTY--vg-home ext4 rw,relatime Files in neuralgic directories: /var: 752M /var/ 390M /var/cache 359M /var/cache/apt 289M /var/cache/apt/archives 281M /var/lib Hint: You are currently not seeing messages from other users and the system. Users in groups 'adm', 'systemd-journal' can see all messages. Pass -q to turn off this notice. Archived and active journals take up 16.0M in the file system. /opt/iobroker/backups: 2.4M /opt/iobroker/backups/ /opt/iobroker/iobroker-data: 136M /opt/iobroker/iobroker-data/ 126M /opt/iobroker/iobroker-data/files 51M /opt/iobroker/iobroker-data/files/javascript.admin 32M /opt/iobroker/iobroker-data/files/javascript.admin/static/js 32M /opt/iobroker/iobroker-data/files/javascript.admin/static The five largest files in iobroker-data are: 9.1M /opt/iobroker/iobroker-data/files/echarts.admin/static/js/2.bbf74d5f.chunk.js.map 8.9M /opt/iobroker/iobroker-data/files/echarts/static/js/2.3d2d025f.chunk.js.map 8.9M /opt/iobroker/iobroker-data/files/echarts.admin/chart/static/js/2.3d2d025f.chunk.js.map 6.9M /opt/iobroker/iobroker-data/files/javascript.admin/static/js/610.de0231c9.chunk.js.map 6.3M /opt/iobroker/iobroker-data/files/admin.admin/custom/static/js/vendors-node_modules_iobroker_adapter-react-v5_assets_devices_parseNames_js-node_modules_iobr-99c23e.847b8ad9.chunk.js.map *** NodeJS-Installation *** /usr/bin/nodejs v18.16.0 /usr/bin/node v18.16.0 /usr/bin/npm 9.5.1 /usr/bin/npx 9.5.1 nodejs: Installed: 18.16.0-deb-1nodesource1 Candidate: 18.16.0-deb-1nodesource1 Version table: *** 18.16.0-deb-1nodesource1 500 500 https://deb.nodesource.com/node_18.x bullseye/main amd64 Packages 100 /var/lib/dpkg/status 12.22.12~dfsg-1~deb11u4 500 500 http://security.debian.org/debian-security bullseye-security/main amd64 Packages 12.22.12~dfsg-1~deb11u3 500 500 http://deb.debian.org/debian bullseye/main amd64 Packages Temp directories causing npm8 problem: 0 No problems detected *** ioBroker-Installation *** ioBroker Status iobroker is running on this host. Objects type: jsonl States type: jsonl MULTIHOSTSERVICE/enabled: false Core adapters versions js-controller: 4.0.24 admin: 6.3.5 javascript: 6.1.4 Adapters from github: 0 Adapter State + system.adapter.admin.0 : admin : SMARTY - enabled, port: 8081, bind: 0.0.0.0, run as: admin + system.adapter.backitup.0 : backitup : SMARTY - enabled + system.adapter.discovery.0 : discovery : SMARTY - enabled + system.adapter.echarts.0 : echarts : SMARTY - enabled + system.adapter.fritzdect.0 : fritzdect : SMARTY - enabled + system.adapter.influxdb.0 : influxdb : SMARTY - enabled, port: 8086 + system.adapter.jarvis.0 : jarvis : SMARTY - enabled + system.adapter.javascript.0 : javascript : SMARTY - enabled system.adapter.net-tools.0 : net-tools : SMARTY - disabled system.adapter.ping.0 : ping : SMARTY - disabled + system.adapter.smartmeter.0 : smartmeter : SMARTY - enabled + system.adapter.web.0 : web : SMARTY - enabled, port: 8082, bind: 0.0.0.0, run as: admin + instance is alive Enabled adapters with bindings + system.adapter.admin.0 : admin : SMARTY - enabled, port: 8081, bind: 0.0.0.0, run as: admin + system.adapter.influxdb.0 : influxdb : SMARTY - enabled, port: 8086 + system.adapter.web.0 : web : SMARTY - enabled, port: 8082, bind: 0.0.0.0, run as: admin ioBroker-Repositories stable : http://download.iobroker.net/sources-dist.json beta : http://download.iobroker.net/sources-dist-latest.json Active repo(s): stable Installed ioBroker-Instances Used repository: stable Adapter "admin" : 6.3.5 , installed 6.3.5 Adapter "backitup" : 2.6.19 , installed 2.6.19 Adapter "discovery" : 3.1.0 , installed 3.1.0 Adapter "echarts" : 1.0.12 , installed 1.0.12 Adapter "fritzdect" : 2.2.6 , installed 2.2.6 Adapter "influxdb" : 3.2.0 , installed 3.2.0 Adapter "jarvis" : 3.1.2 , installed 3.1.2 Adapter "javascript" : 6.1.4 , installed 6.1.4 Controller "js-controller": 4.0.24 , installed 4.0.24 Adapter "net-tools" : 0.2.0 , installed 0.2.0 Adapter "ping" : 1.5.3 , installed 1.5.3 Adapter "simple-api" : 2.7.2 , installed 2.7.2 Adapter "smartmeter" : 3.3.4 , installed 3.3.4 Adapter "socketio" : 4.2.0 , installed 4.2.0 Adapter "tr-064" : 4.2.18 , installed 4.2.18 Adapter "web" : 4.3.0 , installed 4.3.0 Adapter "ws" : 1.3.0 , installed 1.3.0 Objects and States Please stand by - This may take a while Objects: 481 States: 378 *** OS-Repositories and Updates *** Hit:1 http://deb.debian.org/debian bullseye InRelease Hit:2 http://security.debian.org/debian-security bullseye-security InRelease Hit:3 http://deb.debian.org/debian bullseye-updates InRelease Hit:4 http://deb.debian.org/debian bullseye-backports InRelease Hit:5 https://deb.nodesource.com/node_18.x bullseye InRelease Hit:6 https://dl.yarnpkg.com/debian stable InRelease Hit:7 https://repos.influxdata.com/debian stable InRelease Hit:8 https://repos.influxdata.com/debian bullseye InRelease Reading package lists... Pending Updates: 2 *** Listening Ports *** Active Internet connections (only servers) Proto Recv-Q Send-Q Local Address Foreign Address State User Inode PID/Program name tcp 0 0 0.0.0.0:22 0.0.0.0:* LISTEN 0 15379 601/sshd: /usr/sbin tcp 0 0 127.0.0.1:631 0.0.0.0:* LISTEN 0 15394 572/cupsd tcp 0 0 127.0.0.1:9000 0.0.0.0:* LISTEN 1001 102655 10102/iobroker.js-c tcp 0 0 127.0.0.1:9001 0.0.0.0:* LISTEN 1001 102648 10102/iobroker.js-c tcp 0 0 0.0.0.0:8400 0.0.0.0:* LISTEN 1001 103578 10427/io.jarvis.0 tcp6 0 0 :::8082 :::* LISTEN 1001 103439 10247/io.web.0 tcp6 0 0 :::8086 :::* LISTEN 998 18537 525/influxd tcp6 0 0 :::22 :::* LISTEN 0 15381 601/sshd: /usr/sbin tcp6 0 0 ::1:631 :::* LISTEN 0 15393 572/cupsd tcp6 0 0 :::80 :::* LISTEN 0 13077 635/apache2 tcp6 0 0 :::8081 :::* LISTEN 1001 101909 10120/io.admin.0 udp 0 0 0.0.0.0:631 0.0.0.0:* 0 15581 616/cups-browsed udp 0 0 0.0.0.0:58553 0.0.0.0:* 110 1989 500/avahi-daemon: r udp 0 0 0.0.0.0:5353 0.0.0.0:* 110 1987 500/avahi-daemon: r udp6 0 0 :::39214 :::* 110 1990 500/avahi-daemon: r udp6 0 0 fe80::921b:eff:fe3f:546 :::* 0 17949 503/NetworkManager udp6 0 0 :::5353 :::* 110 1988 500/avahi-daemon: r *** Log File - Last 25 Lines *** 2023-05-11 11:47:42.529 - debug: smartmeter.0 (10177) SERIALPORT CLOSE 2023-05-11 11:47:42.530 - debug: smartmeter.0 (10177) SCHEDULE NEXT RUN IN 30s 2023-05-11 11:48:12.531 - debug: smartmeter.0 (10177) CREATE SERIALPORT: 300 7 1 even 2023-05-11 11:48:12.534 - debug: smartmeter.0 (10177) SERIALPORT OPEN 2023-05-11 11:48:12.536 - debug: smartmeter.0 (10177) SET MESSAGE TIMEOUT TIMER: 30000 2023-05-11 11:48:42.537 - debug: smartmeter.0 (10177) MESSAGE TIMEOUT TRIGGERED 2023-05-11 11:48:42.538 - debug: smartmeter.0 (10177) Error: No or too long answer from Serial Device after last request. 2023-05-11 11:48:42.538 - warn: smartmeter.0 (10177) No or too long answer from Serial Device after last request. 2023-05-11 11:48:42.538 - debug: smartmeter.0 (10177) Error: No or too long answer from Serial Device after last request. 2023-05-11 11:48:42.539 - debug: smartmeter.0 (10177) Transport Reset!! Restart = true 2023-05-11 11:48:42.541 - debug: smartmeter.0 (10177) SERIALPORT CLOSE 2023-05-11 11:48:42.542 - debug: smartmeter.0 (10177) SCHEDULE NEXT RUN IN 30s 2023-05-11 11:49:12.543 - debug: smartmeter.0 (10177) CREATE SERIALPORT: 300 7 1 even 2023-05-11 11:49:12.545 - debug: smartmeter.0 (10177) SERIALPORT OPEN 2023-05-11 11:49:12.547 - debug: smartmeter.0 (10177) SET MESSAGE TIMEOUT TIMER: 30000 2023-05-11 11:49:42.547 - debug: smartmeter.0 (10177) MESSAGE TIMEOUT TRIGGERED 2023-05-11 11:49:42.548 - debug: smartmeter.0 (10177) Error: No or too long answer from Serial Device after last request. 2023-05-11 11:49:42.548 - warn: smartmeter.0 (10177) No or too long answer from Serial Device after last request. 2023-05-11 11:49:42.549 - debug: smartmeter.0 (10177) Error: No or too long answer from Serial Device after last request. 2023-05-11 11:49:42.549 - debug: smartmeter.0 (10177) Transport Reset!! Restart = true 2023-05-11 11:49:42.551 - debug: smartmeter.0 (10177) SERIALPORT CLOSE 2023-05-11 11:49:42.552 - debug: smartmeter.0 (10177) SCHEDULE NEXT RUN IN 30s 2023-05-11 11:50:12.551 - debug: smartmeter.0 (10177) CREATE SERIALPORT: 300 7 1 even 2023-05-11 11:50:12.552 - debug: smartmeter.0 (10177) SERIALPORT OPEN 2023-05-11 11:50:12.553 - debug: smartmeter.0 (10177) SET MESSAGE TIMEOUT TIMER: 30000 ============ Mark until here for C&P ============= -
@petlaw sagte in Smartmeter Elster AS1440:
Setz den user 'peter' in die Gruppe 'adm' rein, dann kann der auch logs lesen und du brauchst da keine root-Rechte.
Schalt den Desktop/X-Server aus.
Hit:7 https://repos.influxdata.com/debian stable InRelease
Da ist eine Doublette, vermutich hast du zwei .list-Files zu influx in /etc/apt/sources.list.d/ liegen. Lösche die mit dem Eintrag 'stable'.
Zu deinem eigentlichen Problem mit dem SerialPort fällt mir aber nix ein.
-
@thomas-braun said in Smartmeter Elster AS1440:
@petlaw sagte in Smartmeter Elster AS1440:
Setz den user 'peter' in die Gruppe 'adm' rein, dann kann der auch logs lesen und du brauchst da keine root-Rechte.
Schalt den Desktop/X-Server aus.
Hit:7 https://repos.influxdata.com/debian stable InRelease
Da ist eine Doublette, vermutich hast du zwei .list-Files zu influx in /etc/apt/sources.list.d/ liegen. Lösche die mit dem Eintrag 'stable'.
Zu deinem eigentlichen Problem mit dem SerialPort fällt mir aber nix ein.
Erledigt.
Ich habe mal mit strace gecheckt, ob der Adapter überhaupt auf die Serielle Schnittstelle zugreift, da gibt es aber zu keinem Zeitpunkt einen open call auf /dev/ttyUSB0 oder irgendwas in /dev:
peter@SMARTY:~$ sudo ps -ef | grep smart Debian-+ 1012 892 0 02:52 tty1 00:00:00 /usr/libexec/gsd-smartcard iobroker 10177 10102 0 11:46 ? 00:00:01 io.smartmeter.0 peter 13490 5853 0 11:56 pts/1 00:00:00 grep smart peter@SMARTY:~$ sudo strace -p 10177 strace: Process 10177 attached epoll_wait(14, [], 1024, 41) = 0 epoll_wait(14, [], 1024, 0) = 0 epoll_wait(14, [], 1024, 1000) = 0 epoll_wait(14, [], 1024, 0) = 0 epoll_wait(14, [], 1024, 1000) = 0 epoll_wait(14, [], 1024, 0) = 0 epoll_wait(14, [], 1024, 999) = 0 epoll_wait(14, [], 1024, 0) = 0 epoll_wait(14, [], 1024, 999) = 0 epoll_wait(14, [], 1024, 0) = 0 epoll_wait(14, [], 1024, 999) = 0 epoll_wait(14, [], 1024, 0) = 0 epoll_wait(14, [], 1024, 1000) = 0 epoll_wait(14, [], 1024, 0) = 0 epoll_wait(14, [], 1024, 1000) = 0 epoll_wait(14, [], 1024, 0) = 0 epoll_wait(14, [], 1024, 999) = 0 epoll_wait(14, [], 1024, 0) = 0 epoll_wait(14, [], 1024, 999) = 0 epoll_wait(14, [], 1024, 0) = 0 epoll_wait(14, [], 1024, 1000) = 0 epoll_wait(14, [], 1024, 0) = 0 epoll_wait(14, [], 1024, 1000) = 0 epoll_wait(14, [], 1024, 0) = 0 epoll_wait(14, [], 1024, 1000) = 0 epoll_wait(14, [], 1024, 0) = 0 epoll_wait(14, [], 1024, 1000) = 0 epoll_wait(14, [], 1024, 0) = 0 epoll_wait(14, [], 1024, 1000) = 0 epoll_wait(14, [], 1024, 0) = 0 epoll_wait(14, [], 1024, 51) = 0 epoll_wait(14, [], 1024, 0) = 0 epoll_wait(14, [], 1024, 3) = 0 epoll_wait(14, [], 1024, 0) = 0 epoll_wait(14, [], 1024, 18) = 0 epoll_wait(14, [], 1024, 0) = 0 epoll_wait(14, [], 1024, 1) = 0 epoll_wait(14, [], 1024, 0) = 0 epoll_wait(14, [], 1024, 195) = 0 write(23, "*2\r\n$3\r\nget\r\n$36\r\nio.system.adap"..., 56) = 56 write(23, "*2\r\n$3\r\nget\r\n$40\r\nio.system.adap"..., 60) = 60 futex(0x52740a8, FUTEX_WAKE_PRIVATE, 1) = 1 futex(0x5274040, FUTEX_WAKE_PRIVATE, 1) = 1 openat(AT_FDCWD, "/proc/self/stat", O_RDONLY) = 28 read(28, "10177 (io.smartmeter.0) R 10102 "..., 1023) = 309 close(28) = 0 write(23, "*2\r\n$3\r\nget\r\n$37\r\nio.system.adap"..., 57) = 57 write(23, "*2\r\n$3\r\nget\r\n$43\r\nio.system.adap"..., 63) = 63 write(23, "*2\r\n$3\r\nget\r\n$42\r\nio.system.adap"..., 62) = 62 write(23, "*2\r\n$3\r\nget\r\n$43\r\nio.system.adap"..., 63) = 63 write(23, "*2\r\n$3\r\nget\r\n$37\r\nio.system.adap"..., 57) = 57 write(23, "*2\r\n$3\r\nget\r\n$41\r\nio.system.adap"..., 61) = 61 write(23, "*2\r\n$3\r\nget\r\n$42\r\nio.system.adap"..., 62) = 62 epoll_wait(14, [{EPOLLIN, {u32=23, u64=23}}, {EPOLLIN, {u32=17, u64=17}}], 1024, 0) = 2 read(23, "$118\r\n{\"val\":true,\"ack\":true,\"ts"..., 65536) = 1029 write(23, "*4\r\n$5\r\nsetex\r\n$36\r\nio.system.ad"..., 178) = 178 write(23, "*4\r\n$5\r\nsetex\r\n$40\r\nio.system.ad"..., 182) = 182 write(23, "*3\r\n$3\r\nset\r\n$37\r\nio.system.adap"..., 169) = 169 write(23, "*3\r\n$3\r\nset\r\n$43\r\nio.system.adap"..., 176) = 176 write(23, "*3\r\n$3\r\nset\r\n$42\r\nio.system.adap"..., 175) = 175 write(23, "*3\r\n$3\r\nset\r\n$43\r\nio.system.adap"..., 172) = 172 write(23, "*3\r\n$3\r\nset\r\n$37\r\nio.system.adap"..., 168) = 168 write(23, "*3\r\n$3\r\nset\r\n$41\r\nio.system.adap"..., 170) = 170 write(23, "*3\r\n$3\r\nset\r\n$42\r\nio.system.adap"..., 172) = 172 read(17, "\1\0\0\0\0\0\0\0", 1024) = 8 futex(0x52740a8, FUTEX_WAKE_PRIVATE, 1) = 1 futex(0x5274040, FUTEX_WAKE_PRIVATE, 1) = 1 epoll_wait(14, [{EPOLLIN, {u32=23, u64=23}}, {EPOLLIN, {u32=17, u64=17}}], 1024, 0) = 2 read(23, "+OK\r\n+OK\r\n+OK\r\n+OK\r\n", 65536) = 20 write(23, "*3\r\n$7\r\npublish\r\n$36\r\nio.system."..., 172) = 172 write(23, "*3\r\n$7\r\npublish\r\n$40\r\nio.system."..., 176) = 176 write(23, "*3\r\n$7\r\npublish\r\n$37\r\nio.system."..., 173) = 173 write(23, "*3\r\n$7\r\npublish\r\n$43\r\nio.system."..., 180) = 180 read(17, "\1\0\0\0\0\0\0\0", 1024) = 8 futex(0x52740ac, FUTEX_WAKE_PRIVATE, 1) = 1 futex(0x5274040, FUTEX_WAKE_PRIVATE, 1) = 1 epoll_wait(14, [{EPOLLIN, {u32=23, u64=23}}, {EPOLLIN, {u32=17, u64=17}}], 1024, 0) = 2 read(23, "+OK\r\n+OK\r\n+OK\r\n+OK\r\n+OK\r\n", 65536) = 25 write(23, "*3\r\n$7\r\npublish\r\n$42\r\nio.system."..., 179) = 179 write(23, "*3\r\n$7\r\npublish\r\n$43\r\nio.system."..., 176) = 176 futex(0x6ca1124, FUTEX_WAKE_PRIVATE, 1) = 1 futex(0x6ca10d0, FUTEX_WAKE_PRIVATE, 1) = 1 write(23, "*3\r\n$7\r\npublish\r\n$37\r\nio.system."..., 172) = 172 write(23, "*3\r\n$7\r\npublish\r\n$41\r\nio.system."..., 174) = 174 write(23, "*3\r\n$7\r\npublish\r\n$42\r\nio.system."..., 176) = 176 read(17, "\1\0\0\0\0\0\0\0", 1024) = 8 futex(0x52740ac, FUTEX_WAKE_PRIVATE, 1) = 1 futex(0x5274040, FUTEX_WAKE_PRIVATE, 1) = 1 epoll_wait(14, [{EPOLLIN, {u32=23, u64=23}}, {EPOLLIN, {u32=17, u64=17}}], 1024, 0) = 2 read(23, ":0\r\n:0\r\n:0\r\n:0\r\n:0\r\n:0\r\n:0\r\n:0\r\n", 65536) = 32 read(17, "\1\0\0\0\0\0\0\0", 1024) = 8 futex(0x52740ac, FUTEX_WAKE_PRIVATE, 1) = 1 epoll_wait(14, [], 1024, 0) = 0 epoll_wait(14, [{EPOLLIN, {u32=17, u64=17}}], 1024, 82) = 1 read(17, "\1\0\0\0\0\0\0\0", 1024) = 8 mprotect(0x7043000, 245760, PROT_READ|PROT_WRITE|PROT_EXEC) = 0 mprotect(0x7043000, 245760, PROT_READ|PROT_EXEC) = 0 futex(0x52740ac, FUTEX_WAKE_PRIVATE, 1) = 1 futex(0x5274040, FUTEX_WAKE_PRIVATE, 1) = 1 epoll_wait(14, [{EPOLLIN, {u32=17, u64=17}}], 1024, 0) = 1 read(17, "\1\0\0\0\0\0\0\0", 1024) = 8 write(23, "*2\r\n$3\r\nget\r\n$34\r\nio.system.adap"..., 54) = 54 write(23, "*2\r\n$3\r\nget\r\n$38\r\nio.system.adap"..., 58) = 58 epoll_wait(14, [{EPOLLIN, {u32=23, u64=23}}], 1024, 0) = 1 read(23, ":0\r\n$104\r\n{\"val\":0.13,\"ack\":true"..., 65536) = 116 write(23, "*3\r\n$3\r\nset\r\n$34\r\nio.system.adap"..., 165) = 165 epoll_wait(14, [{EPOLLIN, {u32=23, u64=23}}], 1024, 0) = 1 read(23, "$104\r\n{\"val\":1.79,\"ack\":true,\"ts"..., 65536) = 112 write(23, "*3\r\n$3\r\nset\r\n$38\r\nio.system.adap"..., 170) = 170 epoll_wait(14, [{EPOLLIN, {u32=23, u64=23}}], 1024, 0) = 1 read(23, "+OK\r\n", 65536) = 5 write(23, "*3\r\n$7\r\npublish\r\n$34\r\nio.system."..., 169) = 169 epoll_wait(14, [{EPOLLIN, {u32=23, u64=23}}], 1024, 0) = 1 read(23, "+OK\r\n", 65536) = 5 write(23, "*3\r\n$7\r\npublish\r\n$38\r\nio.system."..., 174) = 174 epoll_wait(14, [{EPOLLIN, {u32=23, u64=23}}], 1024, 0) = 1 read(23, ":0\r\n", 65536) = 4 epoll_wait(14, [], 1024, 0) = 0 epoll_wait(14, [{EPOLLIN, {u32=23, u64=23}}], 1024, 72) = 1 read(23, ":0\r\n", 65536) = 4 epoll_wait(14, [], 1024, 0) = 0 epoll_wait(14, [], 1024, 30) = 0 futex(0x52740a8, FUTEX_WAKE_PRIVATE, 1) = 1 futex(0x5274040, FUTEX_WAKE_PRIVATE, 1) = 1 futex(0x52740a8, FUTEX_WAKE_PRIVATE, 1) = 1 futex(0x5274040, FUTEX_WAKE_PRIVATE, 1) = 1 epoll_wait(14, [{EPOLLIN, {u32=17, u64=17}}], 1024, 0) = 1 read(17, "\1\0\0\0\0\0\0\0", 1024) = 8 write(23, "*3\r\n$7\r\npublish\r\n$26\r\nlog.system"..., 198) = 198 write(23, "*3\r\n$7\r\npublish\r\n$27\r\nlog.system"..., 199) = 199 epoll_wait(14, [{EPOLLIN, {u32=17, u64=17}}, {EPOLLIN, {u32=23, u64=23}}], 1024, 0) = 2 read(17, "\1\0\0\0\0\0\0\0", 1024) = 8 epoll_ctl(14, EPOLL_CTL_ADD, 27, {EPOLLIN, {u32=4294967295, u64=4294967295}}) = 0 epoll_ctl(14, EPOLL_CTL_DEL, 27, 0x7ffe9b261044) = 0 ioctl(27, FIONBIO, [1]) = 0 futex(0x52740a8, FUTEX_WAKE_PRIVATE, 1) = 1 futex(0x5274040, FUTEX_WAKE_PRIVATE, 1) = 1 futex(0x52740a8, FUTEX_WAKE_PRIVATE, 1) = 1 futex(0x5274040, FUTEX_WAKE_PRIVATE, 1) = 1 futex(0x52740ac, FUTEX_WAKE_PRIVATE, 1) = 1 futex(0x5274040, FUTEX_WAKE_PRIVATE, 1) = 1 read(23, ":1\r\n", 65536) = 4 write(23, "*3\r\n$7\r\npublish\r\n$26\r\nlog.system"..., 182) = 182 write(23, "*3\r\n$7\r\npublish\r\n$27\r\nlog.system"..., 183) = 183 epoll_wait(14, [{EPOLLIN, {u32=17, u64=17}}, {EPOLLIN, {u32=23, u64=23}}], 1024, 0) = 2 read(17, "\1\0\0\0\0\0\0\0", 1024) = 8 epoll_ctl(14, EPOLL_CTL_DEL, 27, 0x7ffe9b260dc4) = -1 ENOENT (No such file or di rectory) futex(0x52740ac, FUTEX_WAKE_PRIVATE, 1) = 1 futex(0x5274040, FUTEX_WAKE_PRIVATE, 1) = 1 read(23, ":1\r\n:1\r\n", 65536) = 8 write(23, "*3\r\n$7\r\npublish\r\n$26\r\nlog.system"..., 199) = 199 write(23, "*3\r\n$7\r\npublish\r\n$27\r\nlog.system"..., 200) = 200 epoll_ctl(14, EPOLL_CTL_ADD, 27, {EPOLLIN, {u32=27, u64=27}}) = 0 epoll_wait(14, [{EPOLLIN, {u32=17, u64=17}}, {EPOLLIN, {u32=23, u64=23}}], 1024, 0) = 2 read(17, "\1\0\0\0\0\0\0\0", 1024) = 8 read(23, ":1\r\n:1\r\n", 65536) = 8 epoll_wait(14, [], 1024, 0) = 0 epoll_wait(14, [{EPOLLIN, {u32=23, u64=23}}], 1024, 610) = 1 read(23, ":1\r\n", 65536) = 4 epoll_wait(14, [], 1024, 0) = 0 epoll_wait(14, [], 1024, 568) = 0 epoll_wait(14, [], 1024, 0) = 0 epoll_wait(14, [], 1024, 999) = 0 epoll_wait(14, [], 1024, 0) = 0 epoll_wait(14, [], 1024, 999) = 0 epoll_wait(14, [], 1024, 0) = 0 epoll_wait(14, [], 1024, 1000) = 0 epoll_wait(14, [], 1024, 0) = 0 epoll_wait(14, [], 1024, 1000) = 0 epoll_wait(14, [], 1024, 0) = 0 epoll_wait(14, [], 1024, 1000) = 0 epoll_wait(14, [], 1024, 0) = 0 epoll_wait(14, [], 1024, 1000) = 0 epoll_wait(14, [], 1024, 0) = 0 epoll_wait(14, [], 1024, 1000) = 0 epoll_wait(14, [], 1024, 0) = 0 epoll_wait(14, [], 1024, 1000) = 0 epoll_wait(14, [], 1024, 0) = 0 epoll_wait(14, [], 1024, 999) = 0 epoll_wait(14, [], 1024, 0) = 0 epoll_wait(14, [], 1024, 999) = 0 epoll_wait(14, [], 1024, 0) = 0 epoll_wait(14, [], 1024, 999) = 0 epoll_wait(14, [], 1024, 0) = 0 epoll_wait(14, [], 1024, 1000) = 0 epoll_wait(14, [], 1024, 0) = 0 epoll_wait(14, [], 1024, 1000) = 0 epoll_wait(14, [], 1024, 0) = 0 epoll_wait(14, [], 1024, 1000) = 0 epoll_wait(14, [], 1024, 0) = 0 epoll_wait(14, [], 1024, 249) = 0 write(23, "*2\r\n$3\r\nget\r\n$36\r\nio.system.adap"..., 56) = 56 write(23, "*2\r\n$3\r\nget\r\n$40\r\nio.system.adap"..., 60) = 60 futex(0x52740ac, FUTEX_WAKE_PRIVATE, 1) = 1 futex(0x5274040, FUTEX_WAKE_PRIVATE, 1) = 1 openat(AT_FDCWD, "/proc/self/stat", O_RDONLY) = 29 read(29, "10177 (io.smartmeter.0) R 10102 "..., 1023) = 309 close(29) = 0 write(23, "*2\r\n$3\r\nget\r\n$37\r\nio.system.adap"..., 57) = 57 write(23, "*2\r\n$3\r\nget\r\n$43\r\nio.system.adap"..., 63) = 63 write(23, "*2\r\n$3\r\nget\r\n$42\r\nio.system.adap"..., 62) = 62 write(23, "*2\r\n$3\r\nget\r\n$43\r\nio.system.adap"..., 63) = 63 write(23, "*2\r\n$3\r\nget\r\n$37\r\nio.system.adap"..., 57) = 57 write(23, "*2\r\n$3\r\nget\r\n$41\r\nio.system.adap"..., 61) = 61 write(23, "*2\r\n$3\r\nget\r\n$42\r\nio.system.adap"..., 62) = 62 epoll_wait(14, [{EPOLLIN, {u32=23, u64=23}}, {EPOLLIN, {u32=17, u64=17}}], 1024, 0) = 2 read(23, "$118\r\n{\"val\":true,\"ack\":true,\"ts"..., 65536) = 364 write(23, "*4\r\n$5\r\nsetex\r\n$36\r\nio.system.ad"..., 178) = 178 write(23, "*4\r\n$5\r\nsetex\r\n$40\r\nio.system.ad"..., 182) = 182 write(23, "*3\r\n$3\r\nset\r\n$37\r\nio.system.adap"..., 170) = 170 read(17, "\1\0\0\0\0\0\0\0", 1024) = 8 futex(0x52740ac, FUTEX_WAKE_PRIVATE, 1) = 1 futex(0x5274040, FUTEX_WAKE_PRIVATE, 1) = 1 epoll_wait(14, [{EPOLLIN, {u32=23, u64=23}}, {EPOLLIN, {u32=17, u64=17}}], 1024, 0) = 2 read(23, "$105\r\n{\"val\":26.75,\"ack\":true,\"t"..., 65536) = 665 write(23, "*3\r\n$3\r\nset\r\n$43\r\nio.system.adap"..., 176) = 176 write(23, "*3\r\n$3\r\nset\r\n$42\r\nio.system.adap"..., 174) = 174 write(23, "*3\r\n$3\r\nset\r\n$43\r\nio.system.adap"..., 172) = 172 write(23, "*3\r\n$3\r\nset\r\n$37\r\nio.system.adap"..., 168) = 168 write(23, "*3\r\n$3\r\nset\r\n$41\r\nio.system.adap"..., 170) = 170 write(23, "*3\r\n$3\r\nset\r\n$42\r\nio.system.adap"..., 172) = 172 read(17, "\1\0\0\0\0\0\0\0", 1024) = 8 futex(0x52740a8, FUTEX_WAKE_PRIVATE, 1) = 1 futex(0x5274040, FUTEX_WAKE_PRIVATE, 1) = 1 epoll_wait(14, [{EPOLLIN, {u32=23, u64=23}}, {EPOLLIN, {u32=17, u64=17}}], 1024, 0) = 2 read(23, "+OK\r\n+OK\r\n", 65536) = 10 write(23, "*3\r\n$7\r\npublish\r\n$36\r\nio.system."..., 172) = 172 write(23, "*3\r\n$7\r\npublish\r\n$40\r\nio.system."..., 176) = 176 read(17, "\1\0\0\0\0\0\0\0", 1024) = 8 futex(0x52740a8, FUTEX_WAKE_PRIVATE, 1) = 1 futex(0x5274040, FUTEX_WAKE_PRIVATE, 1) = 1 epoll_wait(14, [{EPOLLIN, {u32=23, u64=23}}, {EPOLLIN, {u32=17, u64=17}}], 1024, 0) = 2 read(23, "+OK\r\n", 65536) = 5 write(23, "*3\r\n$7\r\npublish\r\n$37\r\nio.system."..., 174) = 174 read(17, "\1\0\0\0\0\0\0\0", 1024) = 8 futex(0x52740a8, FUTEX_WAKE_PRIVATE, 1) = 1 futex(0x5274040, FUTEX_WAKE_PRIVATE, 1) = 1 epoll_wait(14, [{EPOLLIN, {u32=23, u64=23}}, {EPOLLIN, {u32=17, u64=17}}], 1024, 0) = 2 read(23, "+OK\r\n", 65536) = 5 write(23, "*3\r\n$7\r\npublish\r\n$43\r\nio.system."..., 180) = 180 read(17, "\1\0\0\0\0\0\0\0", 1024) = 8 futex(0x52740a8, FUTEX_WAKE_PRIVATE, 1) = 1 futex(0x5274040, FUTEX_WAKE_PRIVATE, 1) = 1 epoll_wait(14, [{EPOLLIN, {u32=23, u64=23}}, {EPOLLIN, {u32=17, u64=17}}], 1024, 0) = 2 read(23, "+OK\r\n", 65536) = 5 write(23, "*3\r\n$7\r\npublish\r\n$42\r\nio.system."..., 178) = 178 read(17, "\1\0\0\0\0\0\0\0", 1024) = 8 write(23, "*2\r\n$3\r\nget\r\n$34\r\nio.system.adap"..., 54) = 54 write(23, "*2\r\n$3\r\nget\r\n$38\r\nio.system.adap"..., 58) = 58 epoll_wait(14, [{EPOLLIN, {u32=23, u64=23}}], 1024, 0) = 1 read(23, "+OK\r\n+OK\r\n+OK\r\n+OK\r\n:0\r\n:0\r\n", 65536) = 28 write(23, "*3\r\n$7\r\npublish\r\n$43\r\nio.system."..., 176) = 176 write(23, "*3\r\n$7\r\npublish\r\n$37\r\nio.system."..., 172) = 172 write(23, "*3\r\n$7\r\npublish\r\n$41\r\nio.system."..., 174) = 174 write(23, "*3\r\n$7\r\npublish\r\n$42\r\nio.system."..., 176) = 176 epoll_wait(14, [{EPOLLIN, {u32=23, u64=23}}], 1024, 0) = 1 read(23, ":0\r\n:0\r\n:0\r\n$103\r\n{\"val\":0.2,\"ac"..., 65536) = 247 write(23, "*3\r\n$3\r\nset\r\n$34\r\nio.system.adap"..., 165) = 165 write(23, "*3\r\n$3\r\nset\r\n$38\r\nio.system.adap"..., 170) = 170 epoll_wait(14, [{EPOLLIN, {u32=23, u64=23}}], 1024, 0) = 1 read(23, ":0\r\n+OK\r\n", 65536) = 9 write(23, "*3\r\n$7\r\npublish\r\n$34\r\nio.system."..., 169) = 169 epoll_wait(14, [{EPOLLIN, {u32=23, u64=23}}], 1024, 0) = 1 read(23, "+OK\r\n", 65536) = 5 write(23, "*3\r\n$7\r\npublish\r\n$38\r\nio.system."..., 174) = 174 epoll_wait(14, [{EPOLLIN, {u32=23, u64=23}}], 1024, 0) = 1 read(23, ":0\r\n", 65536) = 4 epoll_wait(14, [], 1024, 0) = 0 epoll_wait(14, [{EPOLLIN, {u32=23, u64=23}}], 1024, 729) = 1 read(23, ":0\r\n", 65536) = 4 epoll_wait(14, [], 1024, 0) = 0 epoll_wait(14, [], 1024, 687) = 0 epoll_wait(14, [], 1024, 0) = 0 epoll_wait(14, [], 1024, 1000) = 0 epoll_wait(14, [], 1024, 0) = 0 epoll_wait(14, [], 1024, 999) = 0 epoll_wait(14, [], 1024, 0) = 0 epoll_wait(14, [], 1024, 999) = 0 epoll_wait(14, [], 1024, 0) = 0 epoll_wait(14, [], 1024, 1000) = 0 epoll_wait(14, [], 1024, 0) = 0 epoll_wait(14, [], 1024, 1000) = 0 epoll_wait(14, [], 1024, 0) = 0 epoll_wait(14, [], 1024, 1000) = 0 epoll_wait(14, [], 1024, 0) = 0 epoll_wait(14, [], 1024, 1000) = 0 epoll_wait(14, [], 1024, 0) = 0 epoll_wait(14, [], 1024, 1000) = 0 epoll_wait(14, [], 1024, 0) = 0 epoll_wait(14, [], 1024, 999) = 0 epoll_wait(14, [], 1024, 0) = 0 epoll_wait(14, [], 1024, 999) = 0 epoll_wait(14, [], 1024, 0) = 0 epoll_wait(14, [], 1024, 1000) = 0 epoll_wait(14, [], 1024, 0) = 0 epoll_wait(14, [], 1024, 1000) = 0 epoll_wait(14, [], 1024, 0) = 0 epoll_wait(14, [], 1024, 1000) = 0 epoll_wait(14, [], 1024, 0) = 0 epoll_wait(14, [], 1024, 1000) = 0 epoll_wait(14, [], 1024, 0) = 0 epoll_wait(14, [], 1024, 226) = 0 write(23, "*2\r\n$3\r\nget\r\n$36\r\nio.system.adap"..., 56) = 56 write(23, "*2\r\n$3\r\nget\r\n$40\r\nio.system.adap"..., 60) = 60 futex(0x52740ac, FUTEX_WAKE_PRIVATE, 1) = 1 futex(0x5274040, FUTEX_WAKE_PRIVATE, 1) = 1 openat(AT_FDCWD, "/proc/self/stat", O_RDONLY) = 29 read(29, "10177 (io.smartmeter.0) R 10102 "..., 1023) = 309 close(29) = 0 write(23, "*2\r\n$3\r\nget\r\n$37\r\nio.system.adap"..., 57) = 57 write(23, "*2\r\n$3\r\nget\r\n$43\r\nio.system.adap"..., 63) = 63 write(23, "*2\r\n$3\r\nget\r\n$42\r\nio.system.adap"..., 62) = 62 write(23, "*2\r\n$3\r\nget\r\n$43\r\nio.system.adap"..., 63) = 63 write(23, "*2\r\n$3\r\nget\r\n$37\r\nio.system.adap"..., 57) = 57 write(23, "*2\r\n$3\r\nget\r\n$41\r\nio.system.adap"..., 61) = 61 write(23, "*2\r\n$3\r\nget\r\n$42\r\nio.system.adap"..., 62) = 62 epoll_wait(14, [{EPOLLIN, {u32=23, u64=23}}, {EPOLLIN, {u32=17, u64=17}}], 1024, 0) = 2 read(23, "$118\r\n{\"val\":true,\"ack\":true,\"ts"..., 65536) = 919 mprotect(0xac90e6c0000, 262144, PROT_READ|PROT_WRITE) = 0 mprotect(0x17dcb7700000, 262144, PROT_READ|PROT_WRITE) = 0 mprotect(0x3913740000, 262144, PROT_READ|PROT_WRITE) = 0 mprotect(0x4481bb00000, 262144, PROT_READ|PROT_WRITE) = 0 futex(0x6ca1124, FUTEX_WAKE_PRIVATE, 1) = 1 futex(0x6ca10d0, FUTEX_WAKE_PRIVATE, 1) = 1 futex(0x6ca1124, FUTEX_WAKE_PRIVATE, 1) = 1 futex(0x6ca10d0, FUTEX_WAKE_PRIVATE, 1) = 1 futex(0x6c60e80, FUTEX_WAIT_PRIVATE, 0, NULL) = -1 EAGAIN (Resource temporarily unavailable) futex(0x6c60e08, FUTEX_WAKE_PRIVATE, 1) = 0 futex(0x6ca1124, FUTEX_WAKE_PRIVATE, 1) = 1 futex(0x6ca10d0, FUTEX_WAKE_PRIVATE, 1) = 1 futex(0x6ca1120, FUTEX_WAKE_PRIVATE, 1) = 1 futex(0x6ca10d0, FUTEX_WAKE_PRIVATE, 1) = 1 getpid() = 10177 write(23, "*4\r\n$5\r\nsetex\r\n$36\r\nio.system.ad"..., 178) = 178 write(23, "*4\r\n$5\r\nsetex\r\n$40\r\nio.system.ad"..., 182) = 182 write(23, "*3\r\n$3\r\nset\r\n$37\r\nio.system.adap"..., 169) = 169 write(23, "*3\r\n$3\r\nset\r\n$43\r\nio.system.adap"..., 176) = 176 write(23, "*3\r\n$3\r\nset\r\n$42\r\nio.system.adap"..., 175) = 175 write(23, "*3\r\n$3\r\nset\r\n$43\r\nio.system.adap"..., 172) = 172 write(23, "*3\r\n$3\r\nset\r\n$37\r\nio.system.adap"..., 168) = 168 write(23, "*3\r\n$3\r\nset\r\n$41\r\nio.system.adap"..., 170) = 170 read(17, "\1\0\0\0\0\0\0\0", 1024) = 8 futex(0x52740ac, FUTEX_WAKE_PRIVATE, 1) = 1 futex(0x5274040, FUTEX_WAKE_PRIVATE, 1) = 1 epoll_wait(14, [{EPOLLIN, {u32=23, u64=23}}, {EPOLLIN, {u32=17, u64=17}}], 1024, 0) = 2 read(23, "$102\r\n{\"val\":11,\"ack\":true,\"ts\":"..., 65536) = 125 write(23, "*3\r\n$3\r\nset\r\n$42\r\nio.system.adap"..., 172) = 172 write(23, "*3\r\n$7\r\npublish\r\n$36\r\nio.system."..., 172) = 172 write(23, "*3\r\n$7\r\npublish\r\n$40\r\nio.system."..., 176) = 176 write(23, "*3\r\n$7\r\npublish\r\n$37\r\nio.system."..., 173) = 173 read(17, "\1\0\0\0\0\0\0\0", 1024) = 8 futex(0x52740ac, FUTEX_WAKE_PRIVATE, 1) = 1 futex(0x5274040, FUTEX_WAKE_PRIVATE, 1) = 1 epoll_wait(14, [{EPOLLIN, {u32=23, u64=23}}, {EPOLLIN, {u32=17, u64=17}}], 1024, 0) = 2 read(23, "+OK\r\n+OK\r\n+OK\r\n", 65536) = 15 write(23, "*3\r\n$7\r\npublish\r\n$43\r\nio.system."..., 180) = 180 write(23, "*3\r\n$7\r\npublish\r\n$42\r\nio.system."..., 179) = 179 write(23, "*3\r\n$7\r\npublish\r\n$43\r\nio.system."..., 176) = 176 read(17, "\1\0\0\0\0\0\0\0", 1024) = 8 futex(0x52740ac, FUTEX_WAKE_PRIVATE, 1) = 1 futex(0x5274040, FUTEX_WAKE_PRIVATE, 1) = 1 epoll_wait(14, [{EPOLLIN, {u32=23, u64=23}}, {EPOLLIN, {u32=17, u64=17}}], 1024, 0) = 2 read(23, "+OK\r\n+OK\r\n+OK\r\n", 65536) = 15 write(23, "*3\r\n$7\r\npublish\r\n$37\r\nio.system."..., 172) = 172 write(23, "*3\r\n$7\r\npublish\r\n$41\r\nio.system."..., 174) = 174 write(23, "*3\r\n$7\r\npublish\r\n$42\r\nio.system."..., 176) = 176 read(17, "\1\0\0\0\0\0\0\0", 1024) = 8 futex(0x52740a8, FUTEX_WAKE_PRIVATE, 1) = 1 futex(0x5274040, FUTEX_WAKE_PRIVATE, 1) = 1 epoll_wait(14, [{EPOLLIN, {u32=23, u64=23}}, {EPOLLIN, {u32=17, u64=17}}], 1024, 0) = 2 read(23, ":0\r\n:0\r\n:0\r\n:0\r\n:0\r\n:0\r\n:0\r\n:0\r\n", 65536) = 32 read(17, "\1\0\0\0\0\0\0\0", 1024) = 8 futex(0x52740a8, FUTEX_WAKE_PRIVATE, 1) = 1 futex(0x5274040, FUTEX_WAKE_PRIVATE, 1) = 1 epoll_wait(14, [{EPOLLIN, {u32=17, u64=17}}], 1024, 0) = 1 read(17, "\1\0\0\0\0\0\0\0", 1024) = 8 write(23, "*2\r\n$3\r\nget\r\n$34\r\nio.system.adap"..., 54) = 54 write(23, "*2\r\n$3\r\nget\r\n$38\r\nio.system.adap"..., 58) = 58 epoll_wait(14, [{EPOLLIN, {u32=23, u64=23}}], 1024, 0) = 1 read(23, ":0\r\n$103\r\n{\"val\":0.2,\"ack\":true,"..., 65536) = 115 write(23, "*3\r\n$3\r\nset\r\n$34\r\nio.system.adap"..., 165) = 165 epoll_wait(14, [{EPOLLIN, {u32=23, u64=23}}], 1024, 0) = 1 read(23, "$104\r\n{\"val\":1.85,\"ack\":true,\"ts"..., 65536) = 112 write(23, "*3\r\n$3\r\nset\r\n$38\r\nio.system.adap"..., 170) = 170 epoll_wait(14, [{EPOLLIN, {u32=23, u64=23}}], 1024, 0) = 1 read(23, "+OK\r\n", 65536) = 5 write(23, "*3\r\n$7\r\npublish\r\n$34\r\nio.system."..., 169) = 169 epoll_wait(14, [{EPOLLIN, {u32=23, u64=23}}], 1024, 0) = 1 read(23, "+OK\r\n", 65536) = 5 write(23, "*3\r\n$7\r\npublish\r\n$38\r\nio.system."..., 174) = 174 epoll_wait(14, [{EPOLLIN, {u32=23, u64=23}}], 1024, 0) = 1 read(23, ":0\r\n", 65536) = 4 epoll_wait(14, [], 1024, 0) = 0 epoll_wait(14, [{EPOLLIN, {u32=23, u64=23}}], 1024, 90) = 1 read(23, ":0\r\n", 65536) = 4 epoll_wait(14, [], 1024, 0) = 0 epoll_wait(14, [], 1024, 47) = 0 futex(0x52740a8, FUTEX_WAKE_PRIVATE, 1) = 1 futex(0x5274040, FUTEX_WAKE_PRIVATE, 1) = 1 epoll_ctl(14, EPOLL_CTL_DEL, 27, 0x7ffe9b264604) = 0 futex(0x52740a8, FUTEX_WAKE_PRIVATE, 1) = 1 futex(0x5274040, FUTEX_WAKE_PRIVATE, 1) = 1 mprotect(0x7043000, 245760, PROT_READ|PROT_WRITE|PROT_EXEC) = 0 mprotect(0x7043000, 245760, PROT_READ|PROT_EXEC) = 0 epoll_wait(14, [{EPOLLIN, {u32=17, u64=17}}], 1024, 0) = 1 read(17, "\1\0\0\0\0\0\0\0", 1024) = 8 futex(0x52740ac, FUTEX_WAKE_PRIVATE, 1) = 1 futex(0x5274040, FUTEX_WAKE_PRIVATE, 1) = 1 write(23, "*3\r\n$7\r\npublish\r\n$26\r\nlog.system"..., 192) = 192 write(23, "*3\r\n$7\r\npublish\r\n$27\r\nlog.system"..., 193) = 193 write(23, "*3\r\n$7\r\npublish\r\n$26\r\nlog.system"..., 234) = 234 write(23, "*3\r\n$7\r\npublish\r\n$27\r\nlog.system"..., 235) = 235 write(23, "*3\r\n$7\r\npublish\r\n$26\r\nlog.system"..., 226) = 226 write(23, "*3\r\n$7\r\npublish\r\n$27\r\nlog.system"..., 227) = 227 write(23, "*3\r\n$7\r\npublish\r\n$26\r\nlog.system"..., 234) = 234 write(23, "*3\r\n$7\r\npublish\r\n$27\r\nlog.system"..., 235) = 235 write(23, "*3\r\n$7\r\npublish\r\n$26\r\nlog.system"..., 199) = 199 write(23, "*3\r\n$7\r\npublish\r\n$27\r\nlog.system"..., 200) = 200 write(23, "*3\r\n$7\r\npublish\r\n$26\r\nlog.system"..., 183) = 183 write(23, "*3\r\n$7\r\npublish\r\n$27\r\nlog.system"..., 184) = 184 write(23, "*3\r\n$7\r\npublish\r\n$26\r\nlog.system"..., 191) = 191 write(23, "*3\r\n$7\r\npublish\r\n$27\r\nlog.system"..., 192) = 192 epoll_wait(14, [{EPOLLIN, {u32=17, u64=17}}, {EPOLLIN, {u32=23, u64=23}}], 1024, 0) = 2 read(17, "\1\0\0\0\0\0\0\0", 1024) = 8 futex(0x52740ac, FUTEX_WAKE_PRIVATE, 1) = 1 futex(0x5274040, FUTEX_WAKE_PRIVATE, 1) = 1 read(23, ":1\r\n:1\r\n:1\r\n:1\r\n:1\r\n:1\r\n:1\r\n:1\r\n"..., 65536) = 52 epoll_wait(14, [{EPOLLIN, {u32=17, u64=17}}], 1024, 0) = 1 read(17, "\1\0\0\0\0\0\0\0", 1024) = 8 epoll_wait(14, [], 1024, 0) = 0 epoll_wait(14, [{EPOLLIN, {u32=23, u64=23}}], 1024, 642) = 1 read(23, ":1\r\n", 65536) = 4 epoll_wait(14, [], 1024, 0) = 0 epoll_wait(14, [], 1024, 599) = 0 epoll_wait(14, [], 1024, 0) = 0 epoll_wait(14, [], 1024, 999) = 0 epoll_wait(14, [], 1024, 0) = 0 epoll_wait(14, [], 1024, 999) = 0 epoll_wait(14, [], 1024, 0) = 0 epoll_wait(14, [], 1024, 1000) = 0 epoll_wait(14, [], 1024, 0) = 0 epoll_wait(14, [], 1024, 1000) = 0 epoll_wait(14, [], 1024, 0) = 0 epoll_wait(14, [], 1024, 1000) = 0 epoll_wait(14, [], 1024, 0) = 0 epoll_wait(14, ^C[], 1024, 1000) = 0 epoll_wait(14, [], 1024, 0) = 0Im gegensatz zu socat:
stat("/dev/ttyUSB0", {st_mode=S_IFCHR|0777, st_rdev=makedev(0xbc, 0), ...}) = 0 openat(AT_FDCWD, "/dev/ttyUSB0", O_RDWR|O_APPEND) = 5 -
@petlaw sagte in Smartmeter Elster AS1440:
Im gegensatz zu socat:
dann hat socat die noch nicht freigegeben
oder die Konfiguration im Adapter passt nicht
-
@homoran said in Smartmeter Elster AS1440:
@petlaw sagte in Smartmeter Elster AS1440:
Im gegensatz zu socat:
dann hat socat die noch nicht freigegeben
oder die Konfiguration im Adapter passt nicht
Der Adapter versucht es ja noch nicht einmal.
Es gibt keinen system call open auf irgendwas unterhalb von /dev, weder ttyUSB0 noch den unter /dev/serial/by-id
Wenn da was schief wäre müsste er ja wenigstens einen Versuch (mit einem falschen Device namen oä) machen, oder ?
-
@petlaw sagte in Smartmeter Elster AS1440:
Der Adapter versucht es ja noch nicht einmal.
doch
@petlaw sagte in Smartmeter Elster AS1440:
2023-05-11 11:30:38.783 - debug: smartmeter.0 (8047) CREATE SERIALPORT: 300 7 1 even
nur möglicherweise den falschen
-
@homoran said in Smartmeter Elster AS1440:
@petlaw sagte in Smartmeter Elster AS1440:
Der Adapter versucht es ja noch nicht einmal.
doch
leider nicht.
peter@SMARTY:/dev$ sudo ps -ewwf | grep smart [sudo] password for peter: iobroker 1083 730 0 13:36 ? 00:00:01 io.smartmeter.0 peter 1258 886 0 13:43 pts/0 00:00:00 grep smart peter@SMARTY:/dev$ sudo strace -o strace_smart.trc -p 1083 strace: Process 1083 attached ^Cstrace: Process 1083 detached peter@SMARTY:/dev$ grep open strace_smart.trc openat(AT_FDCWD, "/proc/self/stat", O_RDONLY) = 28 openat(AT_FDCWD, "/proc/self/stat", O_RDONLY) = 28 openat(AT_FDCWD, "/proc/self/stat", O_RDONLY) = 29 openat(AT_FDCWD, "/proc/self/stat", O_RDONLY) = 29 openat(AT_FDCWD, "/proc/self/stat", O_RDONLY) = 28 openat(AT_FDCWD, "/proc/self/stat", O_RDONLY) = 28 openat(AT_FDCWD, "/proc/self/stat", O_RDONLY) = 29@petlaw sagte in Smartmeter Elster AS1440:
2023-05-11 11:30:38.783 - debug: smartmeter.0 (8047) CREATE SERIALPORT: 300 7 1 even
nur möglicherweise den falschen
Zu keinem Zeitpunkt wird ein system call "open" geloggt auf irgendein Device unterhalb von /dev. Auch nicht auf ein falsches.
-
Also die Lösung war (rückblickend betrachtet) so einfach wie einleuchtend: Der Adapter muss auf bidirektionale Kommunikation gestellt werden, ansonsten schickt er dem Smartmeter nicht die Loginsequenz.
Die Standardeinstellung "nur lesen" taugt vermutlich nur für Smartmeter, die die Werte permanent von selbst über die Schnittstelle ausgeben.
-
@petlaw sagte in Smartmeter Elster AS1440:
Die Standardeinstellung taugt vermutlich nur für Smartmeter, die die Werte permanent von selbst über die Schnittstelle ausgeben.
korrekt!
dafür gibt es die Einstellungen.hätte man aber sehen können/ müssen.
readonly und Wakeup - signon - data passt nicht zusammen.
